Overloads are one of the quickest ways to damage a gearbox. A jammed crusher, a seized conveyor or a sudden shock can push torque far above what the drive was sized for, and in mining, quarrying and other heavy industries these events are part of daily work. This guide to gearbox overload protection explains where overloads come from, how to protect against them, and which I-MAK features and options can help.

Where overloads come from

A rock crusher might suddenly jam, a conveyor can seize, or a drilling rig can hit a hard layer. The driven machine stops sharply while the motor and rotating parts keep pushing, and the gearbox takes the strain. On conveyor drives, the same happens when a belt is overloaded or blocked at a transfer point.

Plastic shredder, a machine where gearbox overload protection guards against jams

Sudden jams and shock loads

A single severe jam can crack gear teeth, shear keys or twist a shaft, as the energy stored in the motor rotor and couplings is released into the gearbox in a fraction of a second.

Temperature and lubrication

Extreme heat thins the oil and extreme cold thickens it. Either way the oil film on the gear teeth and bearings becomes less effective, so the same overload does more harm.

Repeated smaller overloads

Frequent starts under load, small jams and torque peaks just above the rating all add up. Over months they cause fatigue cracks in gear teeth and bearings, which can then fail with little warning.

Methods of gearbox overload protection

Good protection combines the right selection with devices that limit torque when something goes wrong.

Select with a sensible service factor

A gearbox service factor expresses a rating margin for the specified duty. Select it using the relevant manufacturer’s load class, running hours and starts-per-hour method. There is no universal factor for every crusher or conveyor, and a higher factor does not make a gearbox immune to a severe jam. Check permitted peak torque separately.

Choose robust gear materials

Case hardened alloy steel gears add inherent resilience. I-MAK gears are made from case hardening steel such as 16MnCr5 and heat treated, to 57 HRC on the IR range and 58 HRC on the YP range, which gives good resistance to wear and fatigue.

Fit a mechanical torque limiter

A mechanical torque limiter restricts transmitted torque by slipping or disconnecting, depending on its design. Select its setting, response, position and reset method for the complete drive train. Common arrangements include:

  • Shear pin couplings: the pin breaks at a set torque and is replaced once the jam is cleared.
  • Breakaway couplings: these disengage at a set torque and can be reset.
  • Friction slip clutches: these slip above a set torque and drive again once the load falls.
  • Fluid couplings: these can soften starting and limit transmitted torque according to their characteristic. Sustained slip generates heat, so thermal protection and the selected coupling’s instructions matter.

For instance, a mine conveyor might use a shear pin in the coupling between the gearbox and head pulley; if the belt jams, the pin shears and the gearbox is spared.

Use electrical controls

Some variable frequency drives offer torque-limiting and overload functions. Check the actual control mode, settings and response; do not assume that any soft starter provides the same protection during running. Stored rotational energy and response time matter during a sudden jam, so the mechanical and electrical protection need to be assessed together. See our VFD and geared motor guide.

Keep the protection working

A bypassed or seized limiter gives no protection. Keep spare shear pins of the correct grade, never swap them for stronger bolts, and check slip settings at planned maintenance and after any jam.

I-MAK features that help with gearbox overload protection

  • Backstop option: available on ranges including IRO and IRNX to restrict reverse rotation. A backstop does not limit forward overload torque and must be selected for its own duty and direction.
  • Rubber ring torque arm: on the IRO, IRNX and YP ranges, rubber rings act as a torque arm and help absorb shocks and vibration.
  • Temperature sensing: oil and motor temperature sensors can flag abnormal heating when appropriately connected and configured. Temperature is not a direct measurement of instantaneous shaft torque. Confirm sensor options for the selected unit; vibration monitoring is a separate condition-monitoring measure.

A separate torque limiter must be specified as part of the drive system. Its location may be on the input or output side, depending on the arrangement and the components being protected. Agree the setting against the permissible loads throughout the drive train, including the consequences of disengagement. Mayr explains the difference between slipping and disconnecting torque limiters.

Fluid couplings are usually fitted with fusible plugs that release the fluid if a sustained overload overheats it, while the gearbox breather vents normal pressure changes in the housing. I-MAK advises checking that the vent plug works, because trapped air builds pressure and can cause leaks at the seals.

Example scenarios

The two examples below are hypothetical. They show how these measures work together.

Example: a crusher drive that keeps jamming

Imagine a quarry crushing circuit with repeated jams and gear damage. First investigate the jam mechanism, measured or calculated peak loads and the existing protection. A revised gearbox and torque-limiter selection may form part of the solution, but increasing gearbox size alone does not remove the cause. Clearing and resetting the machine requires the site’s safe isolation and restart procedure.

Example: a steep overland conveyor

Now picture a steep, heavily loaded overland conveyor driven by a shaft mounted gearbox with an optional backstop and a fluid coupling on the motor. The coupling softens starts and limits torque if the belt jams, while the backstop helps stop the loaded belt running back when the drive stops. The conveyor’s brakes and overall system design hold the load, and the machine must be designed and certified to the relevant standard. We confirm the backstop rating with I-MAK for the exact unit.

Gearbox overload protection: a summary

Gearbox overload protection works like an insurance policy. Select with a sensible margin, fit a torque limiting device suited to the machine, use controls and monitoring for early warning, and keep everything maintained. I-MAK’s own guide to the main reasons for gearbox failure covers the wider causes.

Frequently asked questions

What service factor should I use for a shock loaded machine?

Use the manufacturer’s method for the load class, operating hours and start frequency, then check peak loads and protection separately. A generic factor such as 2.0 is not a complete specification. Send the machine duty and overload history for a selection review.

Is a mechanical torque limiter better than electrical protection?

The choice depends on the overload event, drive inertia, response time and required behaviour after a trip. A mechanical limiter can supplement drive controls, but neither should be assumed to prevent every damaging peak. The protective functions must be coordinated for the machine.

Do I-MAK gearboxes come with a backstop?

A backstop is an option, not standard. It is available on many I-MAK units, including the IRO and IRNX shaft mounted ranges, and is ordered for clockwise or anticlockwise free rotation.

Can I-MAK units be monitored for overload?

Appropriate temperature and vibration monitoring can identify changes that merit investigation. These readings support maintenance; they do not directly measure every overload or replace a correctly specified protective device.

Talk to Advanced Drives

Contact Advanced Drives with the machine duty, motor and gearbox details, and the circumstances of any overload. We can help assess the I-MAK gearbox selection; the complete protection arrangement should be agreed with the machine designer and the relevant device suppliers.