Home › Products › A and AE series
I-MAK A and AE Series Industrial Gear Units
Heavy duty helical gear units, up to 33,000 Nm and 487:1.
Home › Products › A and AE series
Heavy duty helical gear units, up to 33,000 Nm and 487:1.
Eight housing sizes of horizontal helical gear unit for heavy industrial duty, with an AE version for extruders. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.
33,000Nm
Output torqueMaximum, for the largest housing size.
185kW
Motor powerIn I-MAK’s performance tables, from 0.37 kW.
8sizes
Housing sizesFrom size 180 up to size 750.
487:1
Ratio rangeFrom 1.71:1 on the A 200 up to 487:1 on the 4A 750.
Overview
The I-MAK A series is a family of horizontal helical gear units for heavy industrial duty. Eight housing sizes cover maximum output torques from 880 Nm up to 33,000 Nm, with ratios from 1.71:1 to 487:1 and motor powers up to 185 kW in I-MAK’s tables.
The type sets the ratio range. The A 200 covers the lowest ratios, from 1.71:1; the 2A types run up to about 49:1, the 3A types up to 310:1 and the 4A 750 up to 487:1. I-MAK designed the series for heavy duty and hard environments, with gears designed to help prevent noise and vibration through long, hard operation.
The AE is the extruder version. It shares the A’s performance tables but adds an extruder bearing housing on the output, and the 3AE 430 and 501 add an extruder output shaft as well. AE types come in sizes 225 to 750, with a smaller output shaft than the A of the same size.
Advanced Drives is the official UK supplier of I-MAK gearboxes and motors. For background on this class of gearbox, read our guide to heavy industrial gearboxes.
Which I-MAK gearbox?
Key advantages
Eight housing sizes, with maximum output torque from 880 Nm up to 33,000 Nm.
A, 2A, 3A and 4A types cover ratios from 1.71:1 up to 487:1.
The AE adds an extruder bearing housing on the output, in sizes 225 to 750.
I-MAK designed the series for heavy industrial duty, with a robust housing for hard environments.
The gears are designed to help prevent noise and vibration through long, hard operation.
A first oil change after 500 hours, then one every 6,000 hours.
360° view
↻ Click and drag to rotate
Technical data
Eight housing sizes across the A, 2A, 3A and 4A types, with AE extruder versions of sizes 225 to 750. I-MAK gives a maximum torque for every size except 200; the right size for your machine depends on its load, hours and starts, and we check that for you against I-MAK’s performance tables.
| Size | Types | Maximum torque (Nm) | Ratio range | Output shaft, A / AE (mm) | Oil (litres) |
|---|---|---|---|---|---|
| 180 | 2A | 880 | 6.98 to 46.02 | 45 / no AE | 4 |
| 200 | A, 2A | On request | 1.71 to 24.04 | On request / no AE | 10 |
| 225 | 2A, 2AE | 2,040 | 7.32 to 46.69 | 55 / 35 | 7 |
| 275 | 2A, 2AE | 4,107 | 6.26 to 47.50 | 65 / 40 | 10 |
| 350 | 2A, 2AE | 8,000 | 6.50 to 48.97 | 80 / 60 | 18 |
| 430 | 2A, 3A, 2AE, 3AE | 17,000 | 6.18 to 99.05 | 105 / 70 | 25 |
| 501 | 2A, 3A, 2AE, 3AE | 27,000 | 7.28 to 310.01 | 120 / 90 | 32 |
| 750 | 3A, 4A, 3AE | 33,000 | 15.01 to 487.32 | 140 / 115 | 65 |
| Common to every size | A and AE series |
|---|---|
| Gearing | Helical, in a horizontal gear unit, with no bevel stage |
| Types | A 200, 2A, 3A and 4A; AE extruder versions of the 2A and 3A |
| Maximum torque | 880 to 33,000 Nm |
| Ratios | 1.71:1 to 487:1 |
| Motor power | 0.37 to 185 kW |
| Output speed | 1 to 820 rpm, at input speeds of 1,400, 900, 700 and 500 rpm |
| Output | Solid shaft; AE types add an extruder bearing housing |
| Mounting positions | P1 to P9 for A types; P1, P4 and P8 listed for AE types |
| Lubrication | CLP gear oil to DIN 51517-3, mineral or synthetic, chosen for the operating temperature |
| Oil quantity | One quantity per type, the same in every mounting position |
| Oil changes | After the first 500 hours, then every 6,000 hours |
Maximum torques and shaft diameters are the figures on I-MAK’s A and AE product page, not catalogue ratings; the torque for a given ratio and motor comes from the catalogue’s performance tables, and on some types, such as the 4A 750, it is well below the maximum; ratios, motor powers, speeds and oil quantities are from the performance and oil tables in I-MAK’s A series catalogue 2024, Rev.00. The catalogue prints the fifth size as 350 in its tables and 351 on its ordering page. I-MAK’s product page does not list size 200, so its torque and shaft size are on request.
Applications
I-MAK designs the A and AE for heavy industrial duty and hard environments, and names one specific use: extruders, through the AE. It names no particular industries, so we size each unit to your duty: its torque, speed, hours and starts.
The AE types, with an extruder bearing housing on the output
Long, hard running where torque and service factor matter
A robust housing, with anti-corrosion and outdoor paint options
3A and 4A types, for output speeds down to 1 rpm on the 4A 750
The A 200 and 2A types, from 1.71:1, with up to 820 rpm on the A 200
Matching an existing helical gear unit on torque, shafts and mounting
Can’t find it?
Send us the type code from the nameplate, or your torque and speed, and we will send the right drawing.
Replacing a gearbox
Every A and AE unit carries a nameplate. Send us its details, with a few photos, and we will match the replacement.
An A series type code gives the type, such as 3A or 3AE, then the housing size, such as 430. Any options follow a slash, such as OTS for an oil temperature sensor or 111 for special output shaft dimensions.
The type code, ratio and serial number from the nameplate, photos of the nameplate, shafts and mounting, and what the gear unit drives. For an AE, tell us about the extruder.
Tell us how the unit is mounted and which way up. I-MAK lists A types for mounting positions P1 to P9 and AE types for P1, P4 and P8.
We can often replace a gearbox from another maker with an I-MAK unit. Send us the nameplate, shaft and mounting details and we will check the fit.
Ask us for I-MAK spares such as seals and bearings; the parts lists in the A series catalogue help identify them. Need a repair rather than a replacement? Call us and we will talk it through.
Type code
Let’s find your gearbox
We just need three details.
Replacing one? Send us the type code from the nameplate and a photo, and we will work from those.
1
Continuous and peak, at the gear unit output shaft.
2
Output rpm or the ratio, and the motor speed if you already have one.
3
Hours per day, starts per hour, and how the unit is mounted.
Prefer us to call you? Request a callback.
FAQs
Anything else? Call +44 (0)1535 655151 or email sales@advanced-drives.com.
Both are helical gear units and share the same performance tables. The AE is the extruder version: it adds an extruder bearing housing on the output and has a smaller output shaft than the A of the same size.
Eight housing sizes cover maximum output torques from 880 Nm up to 33,000 Nm. The right size depends on your duty, so tell us the load, hours per day and starts per hour and we will check it against I-MAK’s tables.
They are the gearbox types in I-MAK’s ordering code, and each covers a different ratio range: up to about 49:1 for the 2A, 310:1 for the 3A and 487:1 for the 4A. The A 200 covers the lowest ratios, from 1.71:1.
No. The A and AE are helical gear units with no bevel stage, so they do not turn the drive through 90 degrees. For a right-angle drive, look at the IRK or MK series.
A CLP gear oil to DIN 51517-3, mineral or synthetic, with the grade chosen for the operating temperature; food-compatible and low temperature oils are options. Change it after the first 500 hours, then every 6,000 hours, and check the level, breather and fixing bolts in between.
Often, yes. Send us the nameplate details, the shaft and mounting dimensions, and photos, and we will check whether an A or AE fits as a drop-in replacement.