Home › Products › AD, ADS and IRAEM series
I-MAK AD, ADS and IRAEM Series Special Type Gear Units
Twin output shaft gear units for roll forming, up to 8,000 Nm.
Home › Products › AD, ADS and IRAEM series
Twin output shaft gear units for roll forming, up to 8,000 Nm.
Foot mounted gear units with two output shafts, one above the other, designed by I-MAK for roll-forming machines, plus the IRAEM range. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.
8,000Nm
Maximum torqueFor the AD 230 and AD 250.
6sizes
AD and ADS sizesThree AD sizes and three ADS sizes.
1:1
AD ratioA spur gear unit for roll forming.
30:1
ADS ratios7.5:1, 15:1 or 30:1, with a worm stage.
Overview
I-MAK designed the AD and ADS series for the roll form industry. Both are foot mounted, with two solid output shafts, one above the other, to drive the upper and lower roll shafts of a forming station.
The AD is a spur gear unit with a 1:1 ratio, in three sizes up to 8,000 Nm. The ADS adds a worm stage, for ratios of 7.5:1, 15:1 or 30:1, and its input shaft comes out of both sides, so it can be driven from either side. On the ADS 185 and ADS 230 the two output shafts can also be built to run at different speeds, as a forming line often needs the upper roll to turn more slowly.
The IRAEM is a separate range that I-MAK lists with torques from 90 to 1,800 Nm and shaft diameters from 20 to 120 mm. I-MAK publishes no further detail, so if an IRAEM may suit your machine, send us your torque, speed and shaft sizes and we will ask I-MAK for you.
Advanced Drives is the official UK supplier of I-MAK gearboxes and motors. If your machine needs something outside the standard range, read our guide to custom gearbox solutions.
Which I-MAK gearbox?
Key advantages
I-MAK designed both the AD and the ADS for the roll form industry.
Upper and lower solid output shafts, one above the other, on a foot mounted housing.
Three AD sizes from 300 to 8,000 Nm, and three ADS sizes from 1,465 to 6,850 Nm.
The ADS input shaft comes out of both sides of the housing.
On the ADS 185 and ADS 230, the two output shafts can be built with a set speed difference.
Special shafts, couplings, seals, bearings, oils and paint, set by option code on the ADS.
360° view
↻ Click and drag to rotate
Technical data
Three AD sizes and three ADS sizes, all supplied without a motor. I-MAK prints the torque figures as maximum torque; the right size for your line depends on its load, hours and starts, and we check that for you.
| Size | Maximum torque (Nm) | Output shaft centres (mm) | Shaft diameters (mm) |
|---|---|---|---|
| AD 180 | 300 | 180 | 30 |
| AD 230 | 8,000 | 230 | 80 |
| AD 250 | 8,000 | 250 | 80 |
| ADS 185 | 1,465 | 185 | Output 50, input 48 |
| ADS 230 | 4,820 | 230 | Output 80, input 55 |
| ADS 290 | 6,850 | 288 | 75 and 70 |
| IRAEM | 90 to 1,800 | Not published | 20 to 120 |
| Common to every size | AD and ADS series |
|---|---|
| AD gearing | Spur gears, ratio 1:1 |
| ADS gearing | A worm stage and spur gears, with ratios of 7.5:1, 15:1 and 30:1 |
| Outputs | Two solid output shafts, one above the other |
| ADS input | A worm input shaft out of both sides, so the unit can be driven from either side |
| ADS output speeds | Ratio differences between the two output shafts from 1.000 to 1.486, on the ADS 185 and ADS 230 |
| ADS housing | Monobloc, in cast iron |
| Mounting | Foot mounted |
| Motor | Supplied without a motor |
| Lubrication | CLP mineral or CLP HC synthetic gear oil, with the grade chosen for the operating temperature |
| Oil changes | After the first 500 hours, then every 6,000 operating hours |
| Corrosion protection | Paint systems for EN 12944 categories C2 to C5 |
Maximum torques are from I-MAK’s Gearboxes and Drives catalogue 2026, Rev.00, the only I-MAK catalogue that covers the AD; ADS drawings, options, oil and maintenance are from the I-MAK ADK and ADS catalogue 2024, Rev.00, which gives an older ADS range of 1,465 to 2,400 Nm, so we confirm ADS ratings with I-MAK for each order. Shaft sizes and centres were read from I-MAK’s dimension tables and drawings, where the ADS 290 drawing shows a 75 mm and a 70 mm shaft, and the IRAEM figures are from I-MAK’s product page.
Applications
I-MAK designed the AD and ADS for roll-forming machines, where a forming station often drives an upper and a lower roll shaft.
Forming stations with upper and lower roll shafts
Roll-forming lines for steel and aluminium profiles
Roll-forming lines for pipes
Roll-formed cable tray lines
Roll-formed parts for the automotive sector
Sheet metal forming and processing lines
Can’t find it?
Send us the size from the nameplate, or your torque, speed and shaft centres, and we will send the right drawing.
Replacing a gearbox
Start with the nameplate. Send us its details, with a few photos and measurements, and we will match the replacement.
Note the series and size, such as ADS 230, the ratio and the serial number. I-MAK publishes no full type code for these series, so every detail on the plate helps.
The nameplate details, photos of the unit, shafts and mounting, the distance between the output shafts, and what the line makes.
AD and ADS units are foot mounted. Tell us which side the drive comes in from and the height of the shafts above the base, so the replacement lines up with your stand.
We supply replacements for many other gearbox brands. Send us the shaft sizes, the distance between the output shafts, the foot fixing dimensions and the torque, and we will check the fit.
Ask us for I-MAK spares such as seals and bearings; the ADS parts list in I-MAK’s catalogue helps identify them. Need a repair rather than a replacement? Call us and we will talk it through.
Identification
Let’s find your gearbox
We just need three details.
Replacing one? Send us the details from the nameplate and a photo, and we will work from those.
1
Continuous and peak, at the output shafts.
2
Input speed, output speed or ratio, and any speed difference between the upper and lower shafts.
3
The distance between the output shafts, the shaft sizes, and which side the drive comes in from.
Prefer us to call you? Request a callback.
FAQs
Anything else? Call +44 (0)1535 655151 or email sales@advanced-drives.com.
The AD is a spur gear unit with a 1:1 ratio, in three sizes up to 8,000 Nm. The ADS adds a worm stage, for ratios of 7.5:1, 15:1 or 30:1, and its input shaft comes out of both sides, so it can be driven from either side.
On the ADS 185 and ADS 230, yes. I-MAK publishes ratio differences between the two output shafts in steps from 1.000 up to 1.486, as a forming line often needs the upper roll to turn more slowly. Tell us the speeds you need and we will check which step suits.
A range that I-MAK lists with torques from 90 to 1,800 Nm and shaft diameters from 20 to 120 mm. I-MAK publishes no further detail, so send us your torque, speed and shaft sizes and we will ask I-MAK whether an IRAEM suits.
No. I-MAK supplies these units without a motor, so they are driven from your line’s own motor or drive shaft. We can supply I-MAK motors and geared motors separately.
For the ADS, I-MAK lists CLP mineral or CLP HC synthetic gear oils, with the grade chosen for the operating temperature, and food-compatible and low temperature oils as options. I-MAK’s maintenance instructions call for an oil change after the first 500 hours, then every 6,000 operating hours.
Often, yes. Send us the shaft sizes, the distance between the output shafts, the foot fixing dimensions and photos, and we will check whether an AD or ADS fits.