Home › Products › MAE and MKE series

I-MAK MAE and MKE Series Monobloc Extruder Gear Units

Extruder gear units, helical or right angle, up to 70,000 Nm.

Nine housing sizes of monobloc gear unit, with an output built to carry the axial load from an extruder screw. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.

Get a priceSend us your nameplate details
I-MAK MAE monobloc extruder gear unit

70,000Nm

Output torqueMaximum, for the largest housing size.

560kW

Motor powerUp to 560 kW on the MAE and 250 kW on the MKE.

9sizes

Housing sizesFrom size 40 up to size 120, as MAE or MKE.

512:1

Ratio rangeFrom 6.028:1 on the MAE, up to 512:1 on the MKE.

Overview

The I-MAK MAE and MKE: monobloc gear units for extruders

The MAE and MKE are the extruder versions of I-MAK’s monobloc gear units. The MAE follows the helical MA family and the MKE the bevel helical, right-angle MK family, across nine housing sizes with maximum torque up to 70,000 Nm.

The output is a hollow shaft that takes the extruder screw shank, and I-MAK designs it to carry the high axial load the screw puts on the gear unit. I-MAK also gives the MAE and MKE larger roller bearings and extended centre distances, so they can take higher loads.

The housing is a single casting in cast iron, and the gears are 16MnCr5 steel, hardened to 57 HRC and ground. IEC or NEMA inputs, backstop and brake options, a range of cooling and lubrication options, and horizontal or vertical mounting are all available. I-MAK publishes no thrust rating, so tell us the screw thrust and we will check the selection.

Advanced Drives is the official UK supplier of I-MAK gearboxes and motors.

Which I-MAK gearbox?

Choose the MAE or MKE when the gear unit drives an extruder screw

Key advantages

Why choose an I-MAK MAE or MKE

Built for screw thrust

The output is designed to carry the high axial load from an extruder screw.

Up to 70,000 Nm

Nine housing sizes, with maximum torque from 6,080 Nm up to 70,000 Nm.

Larger bearings

Larger roller bearings and extended centre distances, so the unit can take higher loads.

Helical or right angle

The MAE is helical, in the MA family; the MKE adds a bevel stage for a right-angle drive.

Hardened, ground gears

16MnCr5 steel gears, hardened to 57 HRC and ground.

Bore to suit your screw

The hollow output shaft takes the screw shank, and the bore can be made to suit your screw.

360° view

↻ Click and drag to rotate

Technical data

I-MAK MAE and MKE technical specifications

Nine housing sizes, as the helical MAE or the right-angle MKE. The torque figures are I-MAK’s maximum for each size group, and the hollow shaft is the bore that takes the screw shank. The right size for your extruder depends on its torque, speed, screw thrust and hours, and we check that for you.

Housing size MAE maximum torque (Nm) MKE maximum torque (Nm) Hollow shaft bore (mm)
40 MAE 402-403: 6,080 MKE 403-404: 6,100 60
50 MAE 502-503: 10,300 MKE 503-504: 10,300 70
60 MAE 602-603: 12,900 MKE 603-604: 12,900 80
70 MAE 702-703-704: 19,400 MKE 703-704: 19,400 90
80 MAE 802-803-804: 24,100 MKE 803-804: 22,520 100
90 MAE 902-903-904: 29,930 MKE 903-904: 29,530 110
100 MAE 1002-1003-1004: 36,000 MKE 1003-1004: 37,580 120
110 MAE 1102-1103-1104: 50,000 MKE 1103-1104: 50,000 130
120 MAE 1202-1203-1204: 70,000 MKE 1203-1204: 70,000 180 or 140, to be confirmed
Common to every size MAE and MKE series
Gearing MAE: helical, in the MA family. MKE: bevel helical, right angle, in the MK family
Housing Monobloc, in cast iron
Gears 16MnCr5 steel, hardened to 57 HRC and ground
Thrust capacity Not published by I-MAK; tell us your screw thrust and we will check the selection
Ratios MAE 6.028:1 to 423:1; MKE 15.674:1 to 512:1
Motor power MAE 2.2 to 560 kW; MKE 0.55 to 250 kW
Input Solid shaft, IEC flange with coupling, or IEC flange with motor; IEC and NEMA configurations
Output Hollow shaft for the screw shank; the bore can be made to suit your screw
Mounting Horizontal or vertical
Cooling Fan, radiator, serpentine coil and heat exchanger options
Ambient temperature +5 to +60 °C for the gear unit, 0 to 40 °C for standard motors; ask us outside this range
Lubrication CLP gear oil to DIN 51517-3, mineral or synthetic, chosen for the operating temperature
Oil changes After the first 500 hours, then every 6,000 hours
Corrosion protection Paint systems for EN 12944 categories C2 to C5

Torques, hollow shaft bores, ratios and motor powers are from the MAE and MKE size table in I-MAK’s MA MK MKE catalogue 2025, Rev.00, which shares its options, oil and maintenance pages with the MA and MK; gear materials and bearings are from I-MAK’s MAE and MKE product data. Ratios and motor powers are the ranges printed in that size table; the MA and MK performance tables, quoted on our MA and MK page, run to slightly different limits. For size 120 the catalogue prints a 180 mm bore and I-MAK’s product page 140 mm, so we confirm it for each order. I-MAK publishes no performance tables, output speeds or thrust ratings for the extruder versions, so ask us to check a selection against your duty.

Options

Options and configurations

Options are listed in the shared MA, MK and MKE catalogue. Tell us what you need and we will confirm it for your size.

Screw shank bore

The hollow output shaft takes the screw shank, and the bore can be made to suit your screw, with special dimensions, materials, hardening or splines.

Extruder output side

The extruder output can be on the left or the right (EL, ER).

Inputs

A solid input shaft, an IEC flange with a coupling for your own motor, or an IEC flange with a motor. NEMA input flanges are also available.

Motors and brakes

Motors from 2.2 to 560 kW on the MAE and 0.55 to 250 kW on the MKE, with brake, hand release, double brake or encoder options.

Backstop

A backstop stops the output turning back when the drive stops (BSL, BSR). Tell us the direction of rotation.

Cooling and lubrication

Fan, radiator, serpentine coil or heat exchanger cooling (244 to 249), forced lubrication by pump and an expansion tank (216, 217).

Seals, bearings and oil

Fluoroelastomer (FKM) seals, reinforced input or output bearings, synthetic or food-compatible oil, and a low temperature oil for use down to -40 °C.

Paint and monitoring

Paint systems for EN 12944 categories C2 to C5, and an oil temperature sensor (OTS).

Applications

Where MAE and MKE gear units work

I-MAK builds the MAE and MKE for extruders and other heavy applications. It does not name particular materials or industries, so we size each unit to your extruder: its torque, speed, screw thrust and hours.

Extruder drives

Driving the screw, with the output built to carry its axial load

Right-angle layouts

The MKE, where the motor sits at 90 degrees to the screw

Horizontal or vertical

Mounting to suit the machine, in either orientation

Heavy applications

Other high load drives, with larger bearings for higher loads

High power drives

Motors up to 560 kW, with cooling options for long running

Replacing an extruder gearbox

Matched on screw shank bore, thrust, torque and mounting

Downloads

I-MAK MAE and MKE downloads

Current documents and tools from I-MAK. No forms, no sign-up.

MA, MK and MKE catalogue

2025, Rev.00 · Includes the MAE and MKE size table and options · PDF

Download

Operating guide

General I-MAK operating guide, 2024 · Oil and maintenance, in four languages · PDF

Download

Online configurator

I-MAK iGuide, for choosing a gearbox online

Open

Dimension drawing

For your exact size and options · On request

Ask us

Can’t find it?

Need the drawing for your exact unit?

Send us the type code from the nameplate, or your torque and speed, and we will send the right drawing.

Replacing a gearbox

Replacing an existing MAE or MKE

Every MAE and MKE carries a nameplate. Send us its details, with a few photos and the screw shank dimensions, and we will match the replacement.

Read the type code

I-MAK names these units by type and size, such as MAE 703 or MKE 1004. The catalogue’s ordering code is written for the MA and MK, so send us the full nameplate and we will read it for you.

What to send us

The type code, ratio, motor power and serial number from the nameplate, photos of the nameplate, shafts and mounting, the screw shank dimensions and the screw thrust if you know it.

Mounting position

Tell us how the unit is mounted, horizontal or vertical, and which way up. The mounting position sets the oil quantity.

Replacing another make

We can often replace a gearbox from another maker with an I-MAK unit. Send us the nameplate, the screw shank bore and the mounting details and we will check the fit.

Spares and repairs

Ask us for I-MAK spares such as seals and bearings. Need a repair rather than a replacement? Call us and we will talk it through.

Type code

How to read an MAE or MKE type

  1. Type: MAE (helical, in the MA family) or MKE (bevel helical, in the MK family)
  2. Housing size: the first digits, 40 to 120, such as 70 in MAE 703
  3. Final digit: 2, 3 or 4 on the MAE, 3 or 4 on the MKE
  4. Input: a solid input shaft, an IEC flange with a coupling, or an IEC flange with a motor
  5. Extruder output: EL (left) or ER (right) in the option list
  6. Ordering: I-MAK’s ordering legend lists the MA and MK only, so send us the full nameplate

Let’s find your gearbox

Looking for an MAE or MKE gear unit or a price?

We just need three details.

Replacing one? Send us the type code from the nameplate and a photo, and we will work from those.

1

Torque and speed

Continuous and peak torque at the screw, and the screw speed or ratio.

2

Screw thrust

The axial load from the screw, and the screw shank diameter.

3

Duty and layout

Hours per day, starts per hour, mounting, and helical or right angle.

Email us your detailsCall +44 (0)1535 655151

Prefer us to call you? Request a callback.

FAQs

I-MAK MAE and MKE questions

Anything else? Call +44 (0)1535 655151 or email sales@advanced-drives.com.

They are the extruder versions. I-MAK designs the output to carry the high axial load from the extruder screw, with larger roller bearings and extended centre distances, and the hollow output shaft takes the screw shank.

I-MAK does not publish a thrust rating for these units. Tell us the screw thrust, torque and speed when you enquire and we will check the selection.

The MAE is helical, in the MA family. The MKE has a bevel stage, in the MK family, so it turns the drive through 90 degrees.

The 2025 catalogue lists hollow shaft bores from 60 mm on size 40 to 130 mm on size 110, and 180 mm on size 120, although I-MAK’s product page gives 140 mm, so we confirm it for each order. The bore can be made to suit your screw, so send us the shank dimensions.

A CLP gear oil to DIN 51517-3, mineral or synthetic, with the grade chosen for the operating temperature; food-compatible and low temperature oils are options. Change it after the first 500 hours, then every 6,000 hours.

Often, yes. Send us the nameplate details, the screw shank bore, the mounting dimensions and photos, and we will check whether an MAE or MKE fits.