Heavy machines often need a lot of torque from a drive that has to fit into a tight space. Monobloc gearboxes meet this need by placing all the gear stages in a housing cast in one piece. This guide explains how monobloc gearboxes work and how the I-MAK MA, MK, MAE and MKE series differ.

What is a monobloc gearbox?
A monobloc gearbox has a single cast housing that carries every gear stage and bearing. With no bolted joints between gear cases, it acts as one rigid structure.
Why a one piece housing helps
- Rigidity: a single casting resists flexing under heavy load, which helps the gears mesh as designed.
- Alignment: the bearing bores are machined in one housing, which keeps the gears accurately positioned.
- Compact size: the gear stages sit close together, so a high torque drive takes up less room.
The trade off: heat
Compact units hold less oil for the power they carry, so heat is often the limit before torque is. Thermal capacity matters as much as torque when you size a monobloc drive.
The I-MAK MA and MK monobloc gearboxes
The I-MAK MA and MK series are monobloc industrial gear units built for heavy loads. I-MAK designs the MA for heavy loads on a continuous working cycle and the MK for heavy loads and hard conditions.
MA: helical, parallel shaft
The MA version uses helical gearing with parallel input and output shafts. It suits layouts where the motor sits alongside the driven machine.
MK: helical bevel, right angle
The MK version adds one bevel stage to the helical stages, which turns the drive through 90°. The MK therefore gives a right angle drive in a compact arrangement that suits tight spaces.
Key figures
| Feature | MA and MK |
|---|---|
| Housing sizes | Nine |
| Rated torque | Up to 70,000 Nm |
| Ratios | From 3.786:1 (MA) to 512:1 (MK) |
| Geared motors | MA geared motors listed up to 560 kW |
| Housing | Grey cast iron, GG20 grade in the I-MAK catalogue |
| Gears | 16MnCr5 steel, heat treated to 57 HRC and ground |
For comparison, the A and AE industrial series reaches 33,000 Nm, so the MA and MK cover roughly twice that torque.
MAE and MKE: the extruder versions
Extruders put a large axial load on the gearbox output, because the screw pushes back as it builds pressure. For this duty I-MAK offers the MAE and MKE extruder gear units.
- MAE follows the MA: helical gearing with parallel input and output shafts.
- MKE follows the MK: a bevel stage plus helical stages for a right angle drive.
- Both have an output built to take the axial load from the screw, with a hollow output shaft sized for the screw shank.
- I-MAK designs them with larger roller bearings and extended centre distances so they can carry higher loads in a compact housing.
I-MAK does not publish thrust capacity figures for the MAE and MKE. We check the screw thrust and shank details with I-MAK for each application.
Options and configuration
Cooling
Cooling is an option, not standard. I-MAK lists fan, radiator, serpentine coil and heat exchanger cooling, and publishes thermal ratings for each MA and MK size, both with and without cooling.
Mounting and outputs
- Horizontal or vertical mounting, foot or flange mounted.
- Hollow shaft, solid shaft, output flange or shrink disk outputs.
- A torque arm with a rubber element, designed for MA and MK units mounted on the machine shaft.
- Solid input shaft, IEC flange for a motor, or a fitted motor.
Other options
- Backstop, available as an option to stop run back when the drive stops.
- Reinforced output or input bearings.
- Oil temperature sensor and forced lubrication.
- Motor brakes and encoders on geared motors.
- Anti-corrosion paint systems to EN 12944, from C2 to C5.
Where monobloc gearboxes are used
- Extruders: an extruder needs high torque at the screw and an output that takes the screw thrust, which is what the MAE and MKE are built for.
- Mixers and kneaders: large mixers run under heavy, continuous load, often with limited space beside the vessel.
- Mills and shredders: where the layout leaves little room, an MK unit with its right angle drive can still provide the torque needed. See our shredder drive solutions.
- Presses and test stands: a rigid, compact drive suits a gearbox built into a machine frame.
- Winches and heavy handling equipment: a monobloc unit can deliver high torque without extra mounting structures. Where a load is lifted or held, the brake and the system design hold the load, and the machine must be designed and certified to the relevant standard.
Example: upgrading an extruder drive
This hypothetical example shows how selection works. A manufacturer wants to increase the throughput of an existing extrusion line by upgrading the motor and gearbox.
- Layout: the motor sits alongside the extruder, so a helical MAE with parallel shafts is the starting point. If the motor had to sit at 90° to the screw, an MKE would be the choice.
- Output: the MAE’s hollow output shaft is matched to the screw shank, so the gearbox mounts directly to the extruder.
- Thrust: the MAE output is designed to carry the screw’s axial load, so a separate thrust bearing housing may not be needed. We check this against the screw thrust for the line.
- Power and heat: a monobloc unit can often take a higher drive power within a similar footprint, but each case is checked against the unit’s mechanical and thermal ratings, with cooling added if needed.
Maintenance in brief
I-MAK recommends checking the oil level, the breather and the fixing bolts, changing the oil after the first 500 hours of running and then every 6,000 hours.
Frequently asked questions
What is the difference between the MA and the MK?
The MA is a helical unit with parallel input and output shafts. The MK adds one bevel stage to give a right angle drive. Both use the same nine housing sizes and reach up to 70,000 Nm.
Are the MAE and MKE different from the MA and MK?
Yes. They are the extruder versions, with an output built to take the screw’s axial load and a hollow shaft for the screw shank. The MAE is parallel shaft and the MKE is right angle.
Does I-MAK publish thrust ratings for the extruder versions?
No. I-MAK states that the output is designed for the screw’s axial load but gives no thrust figures, so we confirm the screw thrust with I-MAK for each application.
Do MA and MK gear units need cooling?
Not always. I-MAK publishes thermal ratings for each size without cooling and with fan, radiator, serpentine coil or heat exchanger cooling. The need depends on power, duty and ambient temperature.
Can a monobloc gearbox be mounted vertically?
Yes. MA and MK units can be mounted horizontally or vertically, foot or flange mounted, or fitted on the machine shaft with a hollow shaft and torque arm.
Talk to Advanced Drives
Advanced Drives, in Silsden, West Yorkshire, is the official UK supplier of I-MAK gearboxes. Tell us your torque, speed, duty and layout, and we will help you choose the right one of our monobloc gearboxes: MA, MK, MAE or MKE. Contact Advanced Drives to discuss your application.