Most drives can be built from a standard catalogue gearbox and motor. Some cannot: an old gearbox may need replacing on a machine whose maker no longer trades, or a unit may have to work outdoors in a corrosive atmosphere. This article explains which custom gearbox solutions are possible within the I-MAK range, which special units I-MAK makes for particular machines, and how Advanced Drives handles a non-standard request.

Red gear units driving roll forming stands, an example of custom gearbox solutions for a particular machine

When a standard unit is not enough

A special requirement usually comes from one of these situations:

  • Replacing an obsolete gearbox. The new unit has to suit the existing shaft sizes, centre height, fixings and output speed.
  • A tight or unusual space. The machine leaves little room, so the shaft arrangement, mounting or flange matters as much as the rating.
  • A demanding environment. Outdoor, humid, cold or chemically contaminated sites need suitable paint, seals and oil.
  • A combination of features. For example a brake, an encoder and a backstop on one geared motor.

Custom gearbox solutions within the I-MAK range

I-MAK quotes more than 1,000,000 product configurations across its range. In practice, most special requirements are met by starting from a standard series and size, then choosing from I-MAK’s published option lists. You can see the full range on our I-MAK gearboxes, drives and motors page.

Shafts, hollow shafts and flanges

  • Shafts with special dimensions or materials, hardened, threaded or with multiple keys.
  • Hollow shafts with special dimensions, materials or splines on series such as IRO and MA/MK; the YP series has a hollow shaft as standard, and MA/MK can also take a shrink disc.
  • IEC B5, B14 and PAM input flanges, NEMA input flanges on series such as YP and MA/MK, and special flange dimensions.
  • Baseplates and torque arms on MA and MK.

Ratios

Catalogue ratio ranges are already wide, for example 3:1 to 27,000:1 on IR and 4:1 to 32,080:1 on YP. Beyond that, the option lists for series including IR, YP, IRO, IRNX, A, MA/MK, 4DS, ADK and ADS include a ratio outside the catalogue, which I-MAK confirms for each enquiry.

Seals, bearings and oil

  • Seals with special dimensions, materials or configurations.
  • Reinforced input or output bearings, and backstop bearings as an option.
  • Synthetic, food-compatible and cold-resistant oil options. Confirm the lubricant and the complete drive’s temperature limits for the actual operating and starting conditions.
  • On MA and MK, forced lubrication by pump and an expansion tank.

Paint and corrosion protection

I-MAK offers special paint colours and types, including epoxy, acrylic for outdoor use, water based and anti-corrosion paint, with build-ups published for the EN 12944 corrosion categories C2 to C5. The standard ranges described here use cast iron, with aluminium also used on the S series. Confirm any requirement for special housing materials with I-MAK for the exact unit.

Motor options

  • Special voltages and frequencies.
  • Motor protection IP55 as standard, with IP56, IP65 and IP66 as options. These IP ratings apply to the motor.
  • Class F insulation as standard, class H as an option; IE3 as standard, IE4 as an option.
  • Brakes, double brakes, hand release, encoders, thermistors, winding heaters and an external fan.
  • Explosion-proof motor options, with certification confirmed with I-MAK for the exact unit.
  • A gearbox with an IEC flange, ready for a motor you already have.

Custom gearbox solutions for particular machines

I-MAK also makes special type gear units for particular machines. They are not a label for bespoke gearboxes in general.

  • AD and ADS series. Foot mounted units for the roll form industry with two output shafts, one above the other. AD is a 1:1 spur gear unit; ADS combines worm and spur gears, with ratios of 7.5:1, 15:1 or 30:1, and its two output shafts can run at different speeds. See our AD, ADS and IRAEM series page.
  • ADK series. A bevel and spur gear unit for roll forming lines, with two input shafts on one axis so a row of units can be driven by one or two motors. Ratio 1.812:1, maximum torque 2,400 to 3,400 Nm, output shaft distance adaptable to the machine, supplied without a motor. See the ADK series page.
  • Other machine specific ranges. MAE and MKE for extruders, 4DS for aerators, mixers and agitators, IRC for crane hoist drums, and IPR and IPRK planetary units where high torque must fit a small space.

How we handle requests for custom gearbox solutions

  1. You send us the duty. The machine, motor power, speeds or ratio, torque, hours per day, starts per hour, mounting and environment. For a replacement, add the nameplate, photos and key dimensions of the old unit.
  2. We pick the nearest standard unit. We select a series and size with a suitable service factor for the load.
  3. We check the options with I-MAK. Special shafts, ratios or housing machining are confirmed by I-MAK before an order, with drawings for you to check against your machine.
  4. We supply and support it from Silsden, West Yorkshire.

Example: replacing an obsolete conveyor gearbox

This is a hypothetical example. A plant runs a conveyor whose gearbox comes from a maker that no longer trades, and the unit has failed. The engineers measure the shaft diameters, centre height, foot fixings and output speed. We look for an I-MAK unit with a suitable rating, then use special shaft dimensions, a special flange or a baseplate to match the existing connections. The customer checks the drawing before ordering.

The same approach suits other retrofits, for example replacing gearboxes on a line of rollers in a steel plant, where each mounting may differ. I-MAK names rolling mills, hoisting systems and material handling among its tailored solutions for steel and metal processing.

Where a drive lifts or holds a load

For a theatre lift, hoist or similar machine, the brake and the system design hold the load, not the gearbox, and the machine must be designed and certified to the relevant standard. Double brakes with hand release are available as motor options.

Frequently asked questions

Does I-MAK make fully bespoke gearboxes?

Most special requirements are met by tailoring a standard series with I-MAK’s published options. Where a request goes further, we ask I-MAK and tell you plainly if it cannot be done.

Is ADK I-MAK’s range for custom gearboxes?

No. ADK is a twin input bevel and spur gear unit for roll forming lines. Custom work uses the option lists described above.

Can you supply a ratio that is not in the catalogue?

It may be possible. Several series list a ratio outside the catalogue as an option, which I-MAK confirms for each enquiry.

Can I get a stainless steel or IP rated gearbox?

State the required material and protection level when enquiring. Standard housings described here are cast iron or aluminium; any special housing request needs confirmation from I-MAK. Motor IP ratings apply to the motor, so check gearbox protection and any required certification separately for the complete proposed configuration.

Talk to us about your application

If a standard unit does not quite fit, send us the duty and we will check the custom gearbox solutions available from I-MAK. Contact Advanced Drives and our team will help you find a drive that suits your machine.