Water and wastewater treatment plants run around the clock, often outdoors, and the drives that turn their mixers, aerators and pumps have to keep pace. A failed gearbox can hold up a process stage and lead to urgent repair work in a wet, awkward location. This guide covers what treatment duty asks of a drive, which I-MAK water treatment gearboxes suit it and which options to specify. For an overview of the whole sector, see our page on gearboxes for water and wastewater treatment.
Advanced Drives is the official UK supplier of I-MAK gearboxes, geared motors and motors, based in Silsden, West Yorkshire. I-MAK describes its water purification offer as covering the whole treatment cycle, from primary to secondary treatment, for water treatment stations serving cities and industrial areas.

What water treatment asks of a drive
Long running hours outdoors
Aerators, mixers and pumps often run continuously for weeks, so we select each gearbox with a service factor that suits continuous duty, rather than relying on the catalogue torque alone. Many drives also sit outside, exposed to rain, frost and sun.
Damp, corrosive air
Humidity, splashing and chemical dosing all attack paintwork and exposed metal. The paint system on the gear housing and the protection class of the motor matter as much as the gears inside.
Loads on the output shaft
Mixer and aerator impellers put radial load on the output shaft as well as torque. The gearbox needs to suit those loads, and any thrust from the impeller should be checked at the design stage using the full machine data.
Hazardous areas
In many wastewater facilities, parts of the process (for example inside anaerobic digesters) are classified as hazardous zones due to biogas, so equipment there must be certified for that zone.
Awkward access
Drives on bridges, walkways or tank covers are hard to reach. Simple routine checks and sensible oil change intervals help keep maintenance visits planned rather than urgent.
I-MAK water treatment gearboxes
Advanced Drives addresses these challenges with I-MAK gearboxes suited to water treatment environments. I-MAK lists three advantages for its water purification products: adapted to outside conditions, reduced maintenance costs, and easy assembly and maintenance. It names segments including waste treatment, dryer pools, water treatment and recycling, with applications such as dryers, rotating discs and pumps.
4DS aerator gear units for mixers, aerators and agitators
The 4DS aerator type gear unit is the I-MAK range designed for agitators, mixers and aerators in the waste and water treatment industry.
- Three housing sizes: 480, 615 and 750
- Output torque up to 18,547 Nm
- Motors from 1.5 to 90 kW
- Ratios from 8:1 to 145:1
- Foot or flange mounting
- High radial load values in the catalogue tables
- Optional forced lubrication with its own oil pump, plus an expansion tank
- Five cooling options, from fan cooling to radiator and heat exchanger cooling
IPR and IPRK planetary gearboxes for aerators and screw pumps
I-MAK’s load classification tables for the IPR and IPRK planetary gearboxes list water treatment aerators and screw pumps. The range covers 20 sizes, inline (IPR) or right angle (IPRK), with electric or hydraulic motor input. It suits larger drives where high torque is needed in a compact unit.
Helical and worm geared motors for pumps and mixers
I-MAK names its IR inline helical range for pumps and mixers, with rated torques from 85 to 18,000 Nm. The service factor tables for the compact S, IRS and IRSD worm ranges include pumps, mixers and agitators.
Options for water treatment gearboxes
- Corrosion protection: epoxy and anti-corrosion paint options, with EN 12944 paint systems from C2 to C5 published for several ranges such as the YP. I-MAK describes C5 as suited to continuous high humidity and chemical cleaning contamination.
- Sealing and lubrication: special seal materials and configurations, an expansion tank and forced lubrication are available on the 4DS, along with synthetic, cold resistant and food compatible oil options and an oil temperature sensor.
- Motor protection: IP55 as standard, with IP56, IP65 and IP66 options for spray and dust. Thermistors and winding heaters are also available; heaters are commonly used to limit condensation in damp plant rooms.
- Explosion-proof options: explosion-proof motor options for biogas zones, with certification confirmed with I-MAK for the exact unit before supply.
- High torque at low speed: 4DS ratios from 8:1 to 145:1 suit slow impeller speeds.
- Backstops: available as options where reverse rotation must be prevented.
Example applications for water treatment gearboxes
The examples below are hypothetical and show how a drive might be specified. Every real project is sized on its own duty data.
Surface aerator
A 4DS aerator gear unit drives the aeration impeller, with anti-corrosion paint and optional cooling and forced lubrication for continuous duty.
Screw pump
An IPR planetary gearbox drives an Archimedean screw lifting flow into the works. Screw pumps usually need a backstop to stop the screw running back when the drive stops. We confirm the option for the chosen unit, and the pump system as a whole must be designed for that duty.
Sludge screw conveyor
An IRNX, a range I-MAK names for screw conveyors, is one candidate for a dewatering screw. Confirm torque, speed, mounting and the arrangement that carries screw thrust. Specify motor protection and gearbox sealing for the actual exposure; an IP66 motor alone does not establish that the complete drive suits the wet area.
Chemical dosing mixer
A compact worm or helical geared motor agitates a chemical tank, with an explosion-proof motor where biogas may be present and certification confirmed for the unit.
Slow rotating equipment
A helical bevel geared motor turns a slow moving scraper bridge, sized with a service factor for continuous duty and fitted with an optional backstop.
What to send us when choosing a drive
- The machine type, with its output speed and torque
- Running hours per day and starts per hour
- Mounting position and shaft arrangement
- Radial and axial loads on the output shaft, from the machine designer
- Site conditions: indoor or outdoor, humidity, chemicals and temperature range
- Any hazardous area classification
- Supply voltage, and whether an inverter will be used
FAQ
Which I-MAK gearbox is designed for aerators and mixers?
The 4DS. I-MAK designed it for agitators, mixers and aerators in waste and water treatment. It comes in three sizes: 480, 615 and 750.
Are I-MAK gearboxes IP rated?
Check the exact unit documentation. I-MAK lists motor protection options including IP55, IP56, IP65 and IP66, but a motor rating does not establish the protection of the gearbox or complete drive. Confirm gearbox seals, corrosion protection, installation and any required certification against the treatment-plant environment.
Can you supply drives for biogas areas?
I-MAK offers explosion-proof motor options. We confirm the certification with I-MAK for the exact unit before supply, and the equipment must match the zone classification of your site.
How often does a 4DS need an oil change?
The 4DS catalogue recommends the first oil change after 500 hours, then every 6,000 hours, with regular checks of the oil level, vent plug, fastening bolts and alignment. Harsh site conditions may call for more frequent checks.
Can you replace an existing drive on a treatment works?
Often, yes. Send us the nameplate details, the shaft and mounting dimensions, and photos, and we will check whether an I-MAK unit fits.
Talk to Advanced Drives
For guidance on water treatment drive systems, contact Advanced Drives and we will help you choose the right water treatment gearboxes for your mixers, aerators and pumps.