Salt water and salty air attack metal quickly. If your gear drives work on a quayside, at a coastal site or offshore, protecting them from saltwater corrosion means fewer failures and longer service. This guide covers paint systems, seals and fittings, and routine checks.

Why saltwater corrosion is hard on gear drives
Corrosion starts quickly
Bare cast iron and steel can rust within days of salt exposure. Salt holds moisture on the surface, so corrosion carries on after the spray stops, turning surface rust into pitting.
Wet and dry cycles make it worse
A gearbox on a dock might be soaked by spray in the morning and baked in the sun by the afternoon. Each cycle leaves more salt behind and opens small cracks in weak coatings, so even a well painted drive can corrode if the paint system does not suit the site.
Where damage shows first
- Shaft seals: rust where the seal lip runs wears the lip, letting water in and oil out.
- Fasteners and fittings: bolts, drain plugs and breathers often rust first.
- Machined faces and edges: these carry thinner paint, or none.
- The oil: moist air drawn in through the breather can condense inside.
Choose a paint system that resists saltwater corrosion
Understanding EN ISO 12944
EN ISO 12944 is the standard most specifiers use for protective paint systems on steel, grouping sites into corrosivity categories. The current edition runs from C1 to C5, with CX for offshore and other extreme sites. The old C5-M marine category has been merged into C5, so update any specification that still uses it.
| Category | Corrosivity | Typical outdoor examples |
|---|---|---|
| C3 | Medium | Urban and industrial air, coastal areas with low salinity |
| C4 | High | Industrial areas, coastal areas with moderate salinity |
| C5 | Very high | Humid, aggressive industrial areas, coastal areas with high salinity |
| CX | Extreme | Offshore areas with high salinity |
These are examples only; your coatings specialist should confirm the category.
What I-MAK offers
Several I-MAK ranges, including the YP parallel shaft geared motors, IRK, IRC, IRO, MA and MK, and ADK, can be supplied with paint systems for EN 12944 categories C2 to C5. They are built up from a zinc phosphate epoxy primer and an aliphatic acrylic polyurethane topcoat, with a thicker epoxy intermediate coat for C4 and C5. I-MAK describes its C5 system for continuous high humidity and chemical cleaning contamination.
C5 is the highest category I-MAK publishes in its catalogues, and I-MAK does not describe these systems as marine coatings. Ask which category and dry film thickness a system meets and match it to your site. For offshore or CX conditions, talk to us before you order.
Keep the coating intact
- Avoid paint damage during installation and touch up chips straight away.
- Seal machined faces and cut edges after fitting.
- Do not paint over shaft seals, breathers or the nameplate.
A good coating slows rust considerably, provided it is inspected and repaired when damaged.
Seals, shafts and fittings
Seals and shafts
Shaft seals keep oil in and water out. Many I-MAK ranges offer fluoroelastomer (FKM) seals and special seal configurations as options. Protect exposed shaft ends with an anti-corrosion compound or grease. Special shaft materials are also listed as options on several ranges, which we can discuss with I-MAK.
Fasteners and fittings
Agree any change to fasteners, plugs or breathers with the gearbox manufacturer. Material, strength grade, thread engagement, sealing and tightening requirements must remain suitable. Do not add insulating washers or thread compounds as a general corrosion fix: they can alter the joint or tightening conditions. Ask for a compatible, approved corrosion-protection arrangement for the exact unit.
Sacrificial anodes only protect metal sitting in a continuous electrolyte, such as a submerged hull. On a gearbox in air they do little.
Motors
I-MAK three phase motors are IP55 as standard, with IP56, IP65 and IP66 options. For a motor exposed to spray or hosing, ask about IP66. Confirm the exact gearbox’s protection separately; the motor IP rating does not cover the whole drive. The EN 12944 paint systems are published for the gear units, so ask us about the motor finish.
Drainage and breathers
Drainage
- Mount the drive so water runs off rather than collecting around seals, flanges or the terminal box.
- Avoid guards and covers that trap water against the housing, or give them drain holes.
Breathers
As a gearbox warms and cools, it breathes through its breather (vent plug), drawing in moist, salty air. I-MAK’s maintenance guidance says to check the breather works, because a blocked one lets pressure build up and causes leaks at the seals. Make sure it sits correctly for the mounting position, shield it from direct spray, and ask the manufacturer whether a moisture-limiting breather is suitable. Any alternative must preserve the required ventilation and fit the unit’s mounting and pressure conditions.
Inspection and maintenance against saltwater corrosion
- Rinse: wash salt off with fresh water at low pressure, keeping the jet away from seals, then let the unit dry.
- Look: check paint, bolts, seals and breather regularly; wire brush and repaint rust spots.
- Check the oil: a milky appearance, or water at the drain plug, suggests water is getting in.
- Follow the oil intervals: I-MAK’s catalogues for ranges such as the IR, YP and IRO give a first oil change after 500 hours, then every 6,000 hours. On an exposed site, check oil level and condition more often.
Example: drives on a quayside
This is a hypothetical example. Imagine geared motors with a basic enamel finish driving pumps on a harbour wall. After a winter of spray, they show rust at the feet and fasteners, and one seal is weeping oil. A sensible plan:
- Clean back the rust and apply a paint system suited to the site’s EN ISO 12944 category, or specify replacement units with a suitable I-MAK paint system.
- Replace the leaking seal, considering FKM, and check the shaft at the seal track.
- Confirm suitable fastener and breather protection with the manufacturer, preserving specified fixings, ventilation and access.
- Add the drives to a regular rinse and inspection routine.
Frequently asked questions
Which EN ISO 12944 category suits a coastal site?
Usually C3, C4 or C5 depending on salinity, and CX offshore. Your coatings specialist should confirm it.
Are I-MAK gearboxes available in stainless steel?
The standard ranges described here use painted housings. Confirm any requirement for stainless construction or special hardware with I-MAK for the exact unit; do not assume an option is available or excluded across the entire range. Paint, seals, shaft materials and installation details must also suit the exposure.
What IP rating can I get?
I-MAK motor protection options include IP55, IP56, IP65 and IP66. Check the gearbox and complete installation separately against their documentation. An IP rating does not establish corrosion resistance or compatibility with cleaning chemicals.
How often should I inspect a drive near salt water?
Set inspection intervals from the manufacturer’s guidance, exposure, operating duty and observed condition. Inspect promptly after significant salt spray, cleaning or damage. Keep hands-on cleaning and repairs within a safe isolation and maintenance procedure.
Can you help with existing gearboxes?
Yes. Send us the nameplate type code and we can supply I-MAK spares such as seals and bearings.
Talk to Advanced Drives
If you run machinery on the coast or offshore, contact Advanced Drives. We can supply I-MAK gearboxes with anti-corrosion paint systems to EN 12944, up to category C5, and special seal options, and we can advise on protecting existing equipment from saltwater corrosion. I-MAK names marine applications for its IPR and IPRK planetary gearboxes, and our oil and gas page has more. With the right precautions, gear drives can give long, reliable service near salt water.