Food and drink production is hard on drives. Conveyors, mixers, pumps and packing machines run long shifts in wet areas that are cleaned often, and some work in chilled rooms or freezers. This guide explains what to look for in food and beverage gearboxes, which I-MAK options help, and how to choose between the IR, YP, S and MAE ranges.

Bottling line conveyors, a typical duty for food and beverage gearboxes

What food production asks of a drive

  • Cleaning: water and cleaning chemicals attack paint, seals and exposed shafts over time.
  • Contamination risk: oil choice matters as much as sealing.
  • Temperature: cold thickens oil, and moving between warm and cold areas causes condensation.
  • Uptime: a drive that is quick to fit and change reduces lost production.
  • Dust: flour and sugar areas may be classified for explosive atmospheres, which changes the motor you need.

Our food and beverage sector page shows the machines we support across the industry.

What I-MAK offers for food and beverage

I-MAK says it has developed special solutions for the food industry with its customers for more than 50 years. Its food and beverage page sets out these aims:

  • Special paint and lubrication to avoid contamination.
  • Reduced heat for cooled areas.
  • A simplified assembly and coupling system to keep downtime to a minimum.
  • Lower energy use and lower maintenance cost.

I-MAK names packing machines, pumps, extruders and carriers as typical applications for its food and beverage gearboxes.

Options that matter on food and beverage gearboxes

Lubrication

I-MAK catalogue options include food compatible VG 220 oil (212) and cold resistant VG 220 oil described for -40 °C (213). Confirm the exact lubricant and its suitability for the unit, food-safety requirements and operating temperature. The cold-oil option is not, by itself, a -40 °C rating for the complete gearbox and motor.

Paint and corrosion protection

Paint options include epoxy (253) and anti-corrosion (256) systems. On ranges such as the YP, I-MAK publishes anti-corrosion systems to EN 12944 classes C2 to C5. I-MAK gives C5 for continuous high humidity and contamination from chemical cleaning, conditions found in many wet production areas.

Seals and bearings

Gear units can have special seals, including fluoroelastomer seals (225), and a reinforced output bearing (231) for higher shaft loads, such as those from an agitator or a chain driven conveyor.

Motors

  • IP55 as standard, with IP56, IP65 and IP66 options for wetter areas.
  • Anti-condensation winding heaters, and bearings for cold or hot environments.
  • Brakes and encoders.
  • Explosion-proof motor options for dust areas, with certification confirmed with I-MAK for the exact unit.

Choosing food and beverage gearboxes from the I-MAK range

IR helical geared motors

The IR Series has the motor in line with the output, and I-MAK names packaging machinery, conveyors, mixers and pumps among its uses. Its 12 housing sizes are rated from 85 Nm to 18,000 Nm, with geared motors from 0.12 kW to 160 kW.

YP parallel shaft geared motors

The YP Series has a hollow output shaft as standard, so it fits straight onto a conveyor or machine shaft. I-MAK names conveyors as a typical use. Ten sizes cover 130 Nm to 18,000 Nm, with geared motors from 0.12 kW to 200 kW.

S compact worm geared motors

The S Series is a compact right angle unit in nine sizes, rated from 13 Nm to 1,554 Nm, with geared motors from 0.12 kW to 15 kW. Its housing is aluminium or cast iron, so it suits lighter duties such as small conveyors and packing machines.

MAE and MKE extruder gear units

For extruders, the MAE and MKE are I-MAK’s monobloc extruder gear units. The output is built to take the thrust from the screw, with a hollow shaft for the screw shank, in nine housing sizes up to 70,000 Nm.

Packing, filling and labelling machines

Where a machine must stop in an exact position, talk to us about the drive and control arrangement first, and we will match the geared motor to the machine’s speed and duty.

Cold rooms and freezers

For cold rooms and freezers, provide the lowest starting temperature as well as the normal running temperature. Confirm the lubricant, seals, bearings, starting torque and complete motor specification with I-MAK. A cold-resistant oil option alone does not establish freezer suitability, and motor heaters or special bearings must be selected for the actual duty.

Cleaning and maintenance for food and beverage gearboxes

  • Keep high pressure jets away from shaft seals, vent plugs and terminal boxes.
  • Check seals and paint as part of the cleaning routine, and repair paint damage early.
  • Check the oil level and vent plug regularly. Use the operating manual and lubricant instructions for the exact range to set oil-change intervals; do not transfer one interval across every gearbox described here.
  • Avoid direct contact between the drive and the food, as I-MAK’s guide advises.

Examples

These hypothetical examples show how we select food and beverage gearboxes; they are not real installations.

Example: a bottling line conveyor

A drinks plant needs conveyor drives in an area cleaned daily. A YP geared motor may suit the shaft arrangement, subject to load and mounting checks. Compare motor protection, gearbox seals, paint and food-compatible lubricant against the actual cleaning chemicals, temperature and pressure. An IP66 motor or a C5 paint category alone does not establish suitability for the complete cleaning process.

Example: a sauce mixing tank

A sauce kitchen needs a top mounted worm geared motor for a tank agitator. We size an S unit with a service factor for the mixing duty, with epoxy paint and food compatible oil, and check the agitator shaft loads against the output bearing. The oil lowers the risk if a leak ever occurs, but even so, the drive sits away from direct contact with the product.

Frequently asked questions

Which I-MAK gearbox suits a food line?

It depends on the layout and the load: the IR for inline drives, the YP where a hollow shaft helps, the S for compact right angle drives on lighter duties, and the MAE and MKE for extruders. Tell us the torque, speed and duty and we will check the size.

What oil can be used in food areas?

I-MAK lists food compatible VG 220 oil (212) and a cold-resistant oil option (213). These describe different requirements. Confirm the proposed oil against the gearbox specification, operating temperature and your food-safety requirements before supply.

How are the drives protected where cleaning is wet?

Check the complete cleaning process against the proposed motor, gearbox seals, paint and lubricant. I-MAK motor protection options include IP55, IP56, IP65 and IP66. A motor IP rating does not establish the gearbox’s protection or resistance to cleaning chemicals; confirm the exact unit documentation and cleaning instructions.

What are the housings made of?

The IR, YP, IRS and IRSD have cast iron housings, and the S range is aluminium or cast iron. Corrosion protection comes from the paint system, so tell us how the area is cleaned.

Can you replace a drive on an existing food machine?

Often, yes. Send us the nameplate details, the shaft and mounting dimensions, and photos, and we will check whether an I-MAK unit fits.

Talk to Advanced Drives

Advanced Drives is the official UK supplier of I-MAK gearboxes, geared motors and motors, based in Silsden, West Yorkshire. Tell us about the machine and how its area is cleaned, and we will help you specify food and beverage gearboxes, motors, oil and paint to suit. Contact us to discuss your food line.