“Marine grade” is not a single standard for gearboxes. It is shorthand for requirements that help a drive cope with salt, moisture, temperature swings, vibration and the motion of a vessel. This guide explains what buyers usually mean by a marine grade gearbox and what to put in a specification. It is general guidance: Advanced Drives and I-MAK do not claim marine class approval for any I-MAK gearbox or motor.

Engineers fitting an I-MAK YP geared motor to a crane, a duty that calls for a marine grade gearbox specification

What buyers mean by a marine grade gearbox

A “marine grade” specification normally covers five things:

  • Corrosion protection: a paint system rated for air that carries salt and moisture.
  • Sealing: seals and breathers that keep water out of the oil.
  • Materials and fittings: fasteners, plugs and nameplates that will not be the first parts to rust.
  • Duty: sizing for shock loads, intermittent running and, on a vessel, a moving deck.
  • Class approval, where the vessel needs it: design review, witnessed testing and certificates from a classification society.

Not every job needs all five: a quayside conveyor needs corrosion protection and sealing, while a deck crane on a classed vessel may also need approval paperwork.

Corrosion protection

Paint systems to ISO 12944

Protective paint for steel and cast iron is usually specified to ISO 12944, which sets corrosivity categories from C1 (very low) to C5 (very high), plus CX for extreme conditions such as offshore. Older documents use C5-M for marine sites; the current edition has merged this into C5. For salty air on a deck or quayside, specifiers typically ask for C5 or CX.

What I-MAK offers

Several I-MAK ranges, including the YP, IRC, IRO, MA and MK series, can be ordered with anti-corrosion paint systems to EN 12944 categories C2 to C5. I-MAK describes its C5 system as suited to continuous high humidity and contamination from chemical cleaning, not as a marine system, so for salt exposure we confirm the right finish with I-MAK for the exact unit.

Sealing and ingress protection

Water in the oil is a common cause of early gearbox wear at sea. Marine specifications usually look at:

  • Shaft seals, often double lip seals on exposed shafts.
  • Breathers that limit the damp air drawn in as the unit cools.
  • Covers, plugs and drain points that stand up to spray and are easy to check.

State the actual exposure, including spray, cleaning and any risk of immersion. I-MAK lists IP55, IP56, IP65 and IP66 motor protection options. Check the gearbox’s protection and seal configuration separately for the exact unit. A motor IP rating does not establish marine suitability, corrosion resistance or classification-society approval for the complete drive.

Materials, fasteners and fittings

Rust usually starts on the small parts: bolts, plugs, nameplates and bare shaft ends, so buyers often ask for stainless or coated fasteners and protected shaft ends. Mixing metals in salt water can cause galvanic corrosion, so ask what is standard and what can be changed for the specific unit.

Duty: matching a marine grade gearbox to the job

Marine machinery sees shock loads, frequent starts and long idle periods. A vessel also rolls and pitches, which moves the oil inside the gearbox, so tell the manufacturer the mounting position and the angles the unit will see.

IPR and IPRK planetary gearboxes

I-MAK names its IPR and IPRK planetary gearboxes for marine applications. There are 20 sizes, inline (IPR) or right angle (IPRK), with T2max up to 743,990 Nm, electric or hydraulic motor input and negative or modular brake adapters. The catalogue’s load classes include winches, cranes and dredger drives such as cutter heads, slewing gear and manoeuvring winches. We confirm the paint system, seals and any certification needed with I-MAK.

Winches and lifting

Winches and deck lifting gear need a gearbox chosen for the load, duty and braking arrangement. The brake and the system design hold the load, and the machine must be designed and certified to the relevant standard, which on a classed vessel includes the class society’s rules. I-MAK designs its IRC hoist drive for hoist and winch applications; it is not named for marine use, so for a quayside or deck winch we check the finish and paperwork with I-MAK first.

Port conveyors and materials handling

For portside conveyors and materials handling, YP Series parallel shaft geared motors offer good value, with an EN 12944 paint system for exposed sites.

Class approval: when a vessel needs it

Machinery on a classed vessel may need approval from a classification society such as Lloyd’s Register, DNV, ABS or Bureau Veritas, most often for propulsion, steering and some deck machinery. This can involve design review, type approval, testing witnessed by a surveyor and a certificate with the unit, all agreed with the manufacturer before ordering. Many port and shore applications do not need class approval, although the owner or insurer may still ask for test records.

To be clear: Advanced Drives and I-MAK do not claim marine class approval for any I-MAK range. If your project needs it, tell us at the start and we will confirm with I-MAK what can be provided for that unit. For hazardous areas, I-MAK offers explosion-proof motor options, with certification confirmed with I-MAK for the exact unit.

Example: corroded conveyor drives at a port

This is a hypothetical example. A port operator finds the gearboxes on a harbour conveyor rusting and water getting into the oil. For the replacements, they would state the environment (direct salt spray), ask for a suitable ISO 12944 paint category such as C5, review seals, breathers and fasteners, and agree in advance the paperwork their surveyor or insurer wants.

Looking after a marine grade gearbox at sea

  • Touch up paint damage before rust spreads under the coating.
  • Check seals for weeping, and the oil for a milky look, which usually means water.
  • Keep breathers clean and follow the I-MAK operating guide for your unit.

Whole life cost at sea

A better paint system and upgraded seals cost more at the start, but repainting or replacing a drive on a vessel means difficult access and downtime. The lowest purchase price is not always the lowest cost over the life of the unit.

Frequently asked questions

Are I-MAK gearboxes marine class approved?

Advanced Drives and I-MAK do not claim marine class approval for any I-MAK range. If you need it, tell us early so we can confirm with I-MAK what is possible for the exact unit.

Which I-MAK gearboxes are named for marine applications?

The IPR and IPRK planetary gearboxes. Other ranges may suit port and coastal duties with the right finish, which we check case by case.

What paint system should I ask for?

For salty air, usually ISO 12944 C5 or CX. Several I-MAK ranges offer EN 12944 systems up to C5, and we confirm with I-MAK which suits your site.

What IP rating will I get?

Confirm the rating and conditions for the proposed motor and gearbox separately. I-MAK motor options include IP55, IP56, IP65 and IP66. Neither a motor IP rating nor a paint category alone establishes that an assembly is suitable for marine duty.

Talk to Advanced Drives

Send us the duty (load, speed, hours and starts per hour) and the environment (deck, quayside or coastal, temperature range and mounting angles), and we will check the options for a marine grade gearbox with I-MAK. Contact Advanced Drives for a straightforward answer.