Farm and grain store drives work in dust, mud and wet weather, and many then stand idle for months between seasons. Each of these takes its toll on seals, bearings and oil. This guide explains how contamination gets in, how to protect agricultural gearboxes with the options I-MAK gear units and motors offer, and the routines that help them last longer.

Grain auger loading a trailer, a typical duty for agricultural gearboxes

How dust, mud and moisture cause damage

Dust and grit

Grain dust, chaff and soil are fine and abrasive. Once grit gets past a shaft seal it mixes with the oil and grinds away at gears and bearings. It also wears the seal lip, so a small leak tends to get worse.

Mud

Mud packs around shafts and seals and dries into a hard crust. It holds moisture against the housing, hides leaks and blocks motor cooling fins, so the motor runs hotter.

Water and condensation

Water enters past worn seals or through the breather. A warm gearbox that cools quickly, after washing or overnight, draws in damp air that condenses inside. Water turns oil milky, weakens the lubricating film and rusts gears and bearings.

Slurry, fertiliser and chemicals

Ammonia, fertiliser dust and some cleaning products attack paint and bare steel. Once the paint is broken, rust spreads beneath it and fixings become hard to service.

Three layers of defence for agricultural gearboxes

To protect agricultural gearboxes, work on three fronts:

  • Keep contaminants out: tell your supplier about dust, washdown and chemicals at the enquiry stage, choose the motor’s IP rating for the site and keep the breather (vent plug) clean.
  • Resist corrosion: choose a paint system for the corrosion risk, touch up chips early and protect bare shaft ends and fixings.
  • Install with care: choose a mounting position and location that stop water pooling around the seals, and fit guards against mud, stones and spray where the machine allows.

Options to protect agricultural gearboxes

I-MAK does not make a separate range of agricultural gearboxes. Its agriculture work centres on grain storage, processing and milling, alongside forest products. To cope with dusty, muddy and wet conditions, I-MAK gear units can be ordered with protective options; our agricultural drives page gives the wider picture.

Seals and covers

Special seal dimensions and configurations are available, and fluoroelastomer (FKM) seals are an option where heat or chemicals are a concern. A dust cover is listed for some ranges, such as the S and IRSD worm units.

Paint and corrosion protection

Paint options include epoxy, outdoor acrylic and anti-corrosion paint. Several ranges, including the IRO and YP, list paint systems for corrosion categories C2 to C5 to EN 12944. Epoxy is an option rather than the standard finish, so describe the environment when you order.

Motor protection

I-MAK motors are IP55 as standard, with IP56, IP65 and IP66 available as options. Confirm the exact gearbox’s protection and sealing separately; the motor IP rating does not cover the whole drive. Winding heaters (110 V or 220 V) help prevent condensation in a motor that stands idle. Standard motors suit ambient temperatures of 0 to 40 °C; ask us if your site falls outside that.

Shafts, bearings and oil

  • Output shafts can be supplied in special materials or hardened on request.
  • A reinforced output bearing is available for heavier shaft loads.
  • A backstop bearing is an option. It helps stop a loaded inclined conveyor running back, but the conveyor itself must be designed to the relevant standards.
  • Synthetic and cold-resistant oil options are listed on ranges such as the IRO and IRNX. Confirm the complete drive’s lowest starting and running temperatures; an oil option alone is not an assembly temperature rating.

For grain store conveyors: the IRNX

I-MAK names its IRNX shaft mounted gearbox for conveyors and grain storage. It comes in 12 sizes from 515 to 42,700 Nm, and I-MAK describes its housing as designed for easy cleaning and dust resistance.

Caring for agricultural gearboxes through the year

Cleaning without causing damage

  • Remove caked mud and chaff after heavy use, including from the motor fins and fan cover.
  • Use low pressure water and keep the jet away from seals, the breather, the terminal box and cable glands. A strong jet can force water and grit past a seal lip.
  • Let a hot unit cool before washing, so it does not pull damp air in through the breather.

Inspection routine

I-MAK’s maintenance guidance for its IR, IRO and IRNX ranges covers the essentials:

  • Check the oil level and quantity against the I-MAK oil tables.
  • Check that the vent plug works, because trapped air builds pressure and causes leaks at the seals.
  • Check the fastening bolts and watch for vibration from misalignment.
  • Change the oil after the first 500 hours of operation, then every 6,000 hours.

On farm duty, also look for milky oil, weeping seals, damaged paint, a loose torque arm and any change in noise or temperature. A seal costs far less than bearings and gears.

Storage out of season

  • Clean and dry the drive, and store the machine under cover where possible.
  • Check the oil before laying up and change it if it shows signs of water.
  • Protect bare shafts with a rust preventive and keep the breather clear.
  • Follow the manufacturer’s storage instructions for preservation and any shaft rotation. Before turning a shaft, safely isolate the drive and confirm that connected machinery cannot move dangerously.
  • Use motor winding heaters, if fitted, during long idle periods.
  • Before restarting, check the oil, then run the drive under light load first.

Examples

These examples are hypothetical illustrations, not real installations.

Example: a grain store conveyor

A silo conveyor keeps losing bearings to grain dust and washdown water. A sensible specification would be an IRNX gearbox with special seals and an epoxy paint finish, driven by a motor with the IP66 option, plus the backstop option if the conveyor is inclined.

Example: a slurry mixer drive

On a dairy farm, slurry has corroded a painted drive and let water into the oil. The priorities are an anti-corrosion paint system chosen for the site’s corrosion category, FKM seals, a higher IP option on the motor and a mounting position that keeps water off the seals.

Frequently asked questions

Are I-MAK gearboxes IP rated?

Check the exact gearbox and motor documents separately. Motor options include IP55, IP56, IP65 and IP66. Protection of the complete agricultural drive also depends on gearbox seals, ventilation, covers, paint and correct installation.

Which I-MAK gearbox suits a grain store conveyor?

I-MAK names the IRNX shaft mounted range for conveyors and grain storage. Send us the torque, speed and duty, and we will check the size and options.

Can I pressure wash a gearbox?

Use low pressure water, keep the jet off the seals, breather and terminal box, and let a hot unit cool first.

How often should the oil be changed?

The cited guidance for IR, IRO and IRNX gives an initial 500-hour change and subsequent 6,000-hour changes; confirm the manual and lubricant for the installed unit. Investigate milky or otherwise abnormal oil promptly rather than treating its appearance as a complete diagnosis, and address contamination according to the manufacturer’s procedure.

Talk to Advanced Drives

With the right seals, coatings and care, farm operators can protect agricultural gearboxes and extend their life in harsh conditions. Advanced Drives is the official UK supplier of I-MAK gearboxes, geared motors and motors, based in Silsden, West Yorkshire. Tell us about the machine and its conditions, and we will help you choose the right protection. Contact our team for advice or a quotation.