I-MAK ADK Series Roll-Forming Gear Units
Twin input gear units for roll-forming lines, up to 3,400 Nm.
Twin input gear units for roll-forming lines, up to 3,400 Nm.
Gear units with two input shafts on one axis, so a row of them can be driven along a roll-forming line from a single motor or a pair. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.
3,400Nm
Maximum torqueADK 185; the ADK 185-1 is 2,400 Nm.
1.812:1
RatioThrough a bevel stage and spur gears.
2input shafts
Twin inputOn one axis, so units run in a line.
185mm
Output shaft centresOn the ADK 185; can be adapted to your machine.
Overview
I-MAK designed the ADK for roll-forming machines. Each unit has two input shafts on one common axis, one at each end, so identical units can be set in a row and the whole line driven by a single motor or a pair of motors.
Inside, a bevel gear stage and spur gears turn the drive through 90 degrees to the output shafts, at a ratio of 1.812:1. The ADK 185 has two output shafts, one above the other and 185 mm apart, with a maximum torque of 3,400 Nm; the ADK 185-1, with a 261 mm high housing, has a maximum torque of 2,400 Nm.
I-MAK reshaped the housing to cut the distance between neighbouring units, which shortens the line, and the distance between the output shafts can be adapted to the design of your machine. I-MAK describes the housing as a cast iron monobloc, and the units are foot mounted.
Advanced Drives is the official UK supplier of I-MAK gearboxes and motors. If your line needs something outside the standard range, read our guide to custom gearbox solutions.
Which I-MAK gearbox?
Key advantages
Designed by I-MAK for roll-forming machines and profile lines.
Two input shafts on one axis let a row of units be driven by one motor, or two.
The housing is shaped to reduce the gap between neighbouring units, so the line can be shorter.
The ADK 185 has two output shafts, one above the other, 185 mm apart.
The distance between the output shafts can be adapted to your machine.
A cast iron monobloc housing with bevel and spur gearing, for maximum torques up to 3,400 Nm.
Technical data
I-MAK publishes two ADK versions, the ADK 185 and ADK 185-1, both supplied without a motor. The torque figures are printed as maximum torque; the right size depends on your line’s load, hours and starts, and we check that for you.
| Size | Maximum torque (Nm) | Output shafts | Shaft diameters (mm) | Housing height (mm) |
|---|---|---|---|---|
| ADK 185 | 3,400 | Two, one above the other, 185 mm apart | Output 50, input 48 | 460 |
| ADK 185-1 | 2,400 | Ask us for the layout | Output 50, input 48 | 261 |
| Common to every size | ADK series |
|---|---|
| Gearing | A bevel gear stage and spur gears |
| Ratio | 1.812:1 |
| Housing | Monobloc, in cast iron |
| Input | Two input shafts on one common axis, one at each end, 140 mm above the base |
| Output | Solid shafts at right angles to the input axis; the shaft distance can be adapted to your machine |
| Mounting | Foot mounted |
| Motor | Supplied without a motor; a row of units can be driven by one motor or two |
| Lubrication | CLP mineral or CLP HC synthetic gear oil, with the grade chosen for the operating temperature |
| Oil changes | After the first 500 hours, then every 6,000 operating hours |
| Corrosion protection | Paint systems for EN 12944 categories C2 to C5 |
Maximum torques and the ratio are from the I-MAK ADK and ADS catalogue 2024, Rev.00, and I-MAK’s Gearboxes and Drives catalogue 2026, Rev.00; shaft sizes, shaft centres and heights were read from the ADK dimension drawings. I-MAK prints the torque as maximum torque and publishes no power or speed ratings for the ADK.
Applications
The ADK drives the roll stands of roll-forming lines, where a row of units is driven from one or two motors.
Lines of forming stands driven from one or two motors
Roll-forming lines for steel and aluminium profiles
Roll-forming lines for pipes
Roll-formed cable tray lines
Roll-formed parts for the automotive sector
Sheet metal forming and processing lines
Can’t find it?
Send us the size from the nameplate, or your torque, speed and shaft centres, and we will send the right drawing.
Replacing a gearbox
Start with the nameplate on the unit you are replacing. Send us its details, with photos and a few measurements from the line, and we will match the replacement.
Note the series and size, ADK 185 or ADK 185-1, and the serial number. I-MAK publishes no full type code for the ADK, so every detail on the plate helps.
The nameplate details, photos of the unit and its couplings, the distance between the output shafts, and the pitch of the roll stands.
The ADK is foot mounted, with its input shafts 140 mm above the base. Tell us how the units are coupled along the line, so the replacement lines up.
We supply replacements for many other gearbox brands. Send us the torque, speeds, shaft sizes, shaft centres and stand pitch, and we will check whether an ADK fits.
Ask us for I-MAK spares such as seals and bearings; the ADK parts list in I-MAK’s catalogue helps identify them. Need a repair rather than a replacement? Call us and we will talk it through.
Identification
Let’s find your gearbox
We just need three details.
Replacing one? Send us the details from the nameplate and a photo, and we will work from those.
1
Torque at each stand, continuous and peak, and the roll speed or line speed.
2
How many roll stands, and the distance between them along the line.
3
The distance between the upper and lower roll shafts, and the shaft sizes.
Prefer us to call you? Request a callback.
Each ADK has two input shafts on one common axis, one at each end. Neighbouring units are set in a row with their input shafts in line, so the whole row can be driven by a single motor or a pair of motors.
The ADK 185 has a 460 mm high housing, with two output shafts 185 mm apart, and a maximum torque of 3,400 Nm. The ADK 185-1 has a lower housing, 261 mm high, and a maximum torque of 2,400 Nm; both have 50 mm output shafts and 48 mm input shafts.
No. The ADK is supplied without a motor, as the line is driven through the input shafts from one or two motors. We can supply I-MAK motors and geared motors to drive it.
Yes. I-MAK can adapt the distance between the output shafts to the design of your machine; the standard spacing on the ADK 185 is 185 mm. Tell us the spacing you need and we will confirm it with I-MAK.
The catalogue ratio is 1.812:1, through a bevel gear stage and spur gears. Special gears and ratios outside the catalogue can be ordered.
A CLP mineral or CLP HC synthetic gear oil, with the grade chosen for the operating temperature; food-compatible and low temperature oils are options. Change it after the first 500 hours, then every 6,000 operating hours.