I-MAK 4DS Series Aerator Gear Units
Aerator and mixer drive, up to 18,547 Nm and 90 kW.
Aerator and mixer drive, up to 18,547 Nm and 90 kW.
Three sizes of gear unit for aerators, mixers and agitators, with the motor fitted through an adapter and coupling. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.
18,547Nm
Output torqueThe highest in I-MAK’s tables, for the 4DSM 750.
90kW
Motor powerFrom 1.5 kW, with 4, 6 and 8 pole motors.
3sizes
Housing sizesThe 4DSM 480, 615 and 750.
145:1
Ratio rangeFrom 8:1, for output speeds of 4.8 to 175 rpm.
Overview
The I-MAK 4DS series is built to drive agitators, mixers and aerators, with three stages of gearing and a solid output shaft. Three housing sizes cover output torques from 875 Nm up to 18,547 Nm, with motors from 1.5 to 90 kW.
In I-MAK’s tables and parts list the series appears as the 4DSM. The motor fits on a mounting adapter and drives through a coupling, and the unit can be foot or flange mounted. I-MAK designed it to take high loads directly on the shaft, and its performance tables list radial load values (FQl0) of up to 118,000 N for the largest size.
For heavy and complex duties, I-MAK offers extra sealing, pump-fed forced lubrication with an expansion tank, and cooling by fan, radiator or heat exchanger. Output speeds run from 4.8 to 175 rpm across the three sizes.
Advanced Drives is the official UK supplier of I-MAK gearboxes and motors. For background on drives for this kind of plant, read our guide to water treatment drives.
Which I-MAK gearbox?
Key advantages
Three housing sizes, with output torque up to 18,547 Nm in I-MAK’s tables.
Designed to take high loads directly on the shaft; I-MAK’s tables list radial load values (FQl0) up to 118,000 N.
The unit can be foot or flange mounted, to suit the structure it sits on.
Sealing options include fluoroelastomer (FKM) seals, special seal layouts and a bearing seal ring.
Fan, radiator and heat exchanger cooling, and pump-fed forced lubrication, as options.
A first oil change after 500 hours, then one every 6,000 hours.
360° view
↻ Click and drag to rotate
Technical data
Three housing sizes, each driven by a motor through an adapter and coupling. The catalogue gives no single torque rating per size, so the torque figures below are the highest output torques I-MAK lists for each size at a service factor of 1.00 or more; the right size depends on your aerator or mixer duty, and we check that for you.
| Size | 4DSM 480 | 4DSM 615 | 4DSM 750 |
|---|---|---|---|
| Highest output torque in the tables (Nm) | 6,433 | 12,245 | 18,547 |
| Ratios | 8:1 to 145:1 | 13.1:1 to 141:1 | 16.5:1 to 140:1 |
| Output speeds (rpm) | 4.8 to 175 | 5 to 107 | 5 to 85 |
| Motor frames | 90 L to 225 M | 160 M to 250 M | 160 L to 280 M |
| Output shaft diameter (mm) | 105 | 115 | 125 |
| Radial load, FQl0 (N) | 65,000 to 75,000 | 85,000 to 100,000 | 98,000 to 118,000 |
| Oil quantity (litres) | 25 | 35 | 45 |
| Common to every size | 4DS series |
|---|---|
| Gearing | Three gear pairs, driven by a motor through an adapter and coupling |
| Output torque | 875 to 18,547 Nm |
| Ratios | 8:1 to 145:1 |
| Output speeds | 4.8 to 175 rpm |
| Motor power | 1.5 to 90 kW, with 4, 6 and 8 pole motors |
| Standard motor | 400 V 50 Hz, IP 55, class F insulation, IE3 efficiency |
| Output | Solid shaft with key |
| Mounting | Foot or flange mounted; mounting positions P1 to P4 |
| Lubrication | CLP mineral or CLP HC synthetic gear oil to DIN 51517-3, chosen for the operating temperature |
| Oil changes | After the first 500 hours, then every 6,000 hours |
| Motor ambient temperature | 0 to 40 °C as standard; ask us outside this range |
Torques, ratios, speeds, radial loads and motor frames are from I-MAK’s 4DSM performance tables, gear stages from its parts list, and output shaft diameters from I-MAK’s 4DS product data. Source: I-MAK 4DS catalogue 2024, Rev.00.
Applications
I-MAK designed the 4DS for agitators, mixers and aerators, and offers it to the waste and water treatment industry: slow drives that carry high loads directly on the output shaft.
Aerator drives, with high loads taken directly on the shaft
Mixer drives, at output speeds from 4.8 to 175 rpm
Agitators that keep the contents of a tank moving
Aeration and mixing in water treatment plant
Aerators and mixers in wastewater basins and tanks
Mixers and agitators in waste treatment
Can’t find it?
Send us the type code from the nameplate, or your torque and speed, and we will send the right drawing.
Replacing a gearbox
Every I-MAK gear unit carries a nameplate. Send us the details on it, with a few photos, and we will match the replacement.
A 4DS type code is the series and the housing size, such as 4DS 615, with any options after a slash, as in 4DS 615 / OTS – 111 – 363. In I-MAK’s performance tables it appears as the 4DSM, followed by the motor.
The type code, ratio, motor power and serial number from the nameplate, photos of the nameplate, shaft and mounting, and what the unit drives, such as an aerator or mixer.
Tell us how the unit is mounted and which way up. I-MAK lists mounting positions P1 to P4, and the unit holds 25, 35 or 45 litres of oil, depending on size.
We can often replace a gearbox from another maker with an I-MAK unit. Send us the nameplate, shaft and mounting details and we will check the fit.
Ask us for I-MAK spares such as seals and bearings; the parts list in the 4DS catalogue helps identify them. Need a repair rather than a replacement? Call us and we will talk it through.
Type code
Let’s find your gearbox
We just need three details.
Replacing one? Send us the type code from the nameplate and a photo, and we will work from those.
1
An aerator, mixer or agitator, and the output torque or power it needs.
2
Output rpm or the ratio, and the motor power and speed if you already have them.
3
Hours per day, foot or flange mounting, and whether it runs outdoors.
Prefer us to call you? Request a callback.
I-MAK designed the 4DS series for agitators, mixers and aerators, and offers it to the waste and water treatment industry. Output speeds run from 4.8 to 175 rpm, and the unit is designed to take high loads directly on its shaft.
Output torque runs from 875 Nm up to 18,547 Nm, the highest value in I-MAK’s catalogue tables, for the 4DSM 750. The right size depends on the load, speed and hours, so tell us your duty and we will check it.
I-MAK’s ordering code uses 4DS, while its performance tables, oil table and parts list, all in the 4DS catalogue, use 4DSM. In the performance tables the size is followed by the motor, such as 4DSM 615 / 160 M 8b. I-MAK does not explain the extra M, so send us whichever appears on your nameplate.
Yes, as options. I-MAK lists fan and radiator cooling, plate, tubed and brazed heat exchangers, pump-fed forced lubrication and an expansion tank.
A CLP mineral or CLP HC synthetic gear oil to DIN 51517-3, with the grade chosen for the operating temperature. The unit holds 25, 35 or 45 litres depending on size; change the oil after the first 500 hours, then every 6,000 hours.
Often, yes. Send us the nameplate details, the shaft and mounting dimensions, and photos, and we will check whether a 4DS fits.