Home › Products › MA and MK series

I-MAK MA and MK Series Monobloc Gear Units

Parallel shaft or right angle, up to 70,000 Nm and 560 kW.

Nine housing sizes of monobloc gear unit, helical with parallel shafts (MA) or bevel helical at a right angle (MK), with a one-piece cast iron housing. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.

Get a priceSend us your nameplate details
I-MAK MA monobloc gear unit

70,000Nm

Output torqueRated at service factor 1, for the largest size.

560kW

Motor powerMA geared motors from 3 kW; MK from 0.75 to 315 kW.

9sizes

Housing sizesFrom size 40 up to size 120, as MA or MK.

512:1

Ratio rangeFrom 3.786:1 on the MA, up to 512:1 on the MK.

Overview

The I-MAK MA and MK: monobloc gear units for heavy, continuous duty

The I-MAK MA is an all-helical gear unit with parallel input and output shafts; the MK adds a bevel stage to turn the drive through 90 degrees. Both share nine monobloc housing sizes, rated up to 70,000 Nm, with geared motors up to 560 kW on the MA and 315 kW on the MK.

The housing is a single casting in GG20 iron, and the gears are 16MnCr5 steel, hardened to 57 HRC and ground. I-MAK designed the MA for heavy loads on a continuous working cycle, and the MK for heavy loads and hard conditions.

A hollow output shaft is standard, with solid, flanged, shrink disc and extruder outputs as options. The input can be a solid shaft, an IEC flange for your own motor, or an I-MAK motor: at the side on the MA, at the front or on top on the MK. I-MAK publishes thermal ratings for every size, with and without cooling, which matters on high power, continuous drives.

Advanced Drives is the official UK supplier of I-MAK gearboxes and motors.

Which I-MAK gearbox?

Choose the MA or MK for up to 70,000 Nm in a monobloc housing

Key advantages

Why choose an I-MAK MA or MK

Up to 70,000 Nm

Nine housing sizes, rated up to 70,000 Nm at a service factor of 1.

One-piece cast iron housing

A monobloc housing in GG20 cast iron, for heavy loads on a continuous cycle.

Hardened, ground gears

16MnCr5 steel gears, hardened to 57 HRC and ground.

Parallel or right angle

The MA keeps the shafts parallel; the MK turns the drive through 90 degrees in the same housing family.

Published thermal ratings

Ratings for every size without cooling, and with fan and radiator, coil or heat exchanger cooling.

Flexible inputs and outputs

Hollow, solid, flanged, shrink disc and extruder outputs, with a shaft, IEC flange or motor input.

360° view

↻ Click and drag to rotate

Technical data

I-MAK MA and MK technical specifications

Nine housing sizes, each as an MA or MK gear unit or geared motor. The torque figures are I-MAK’s ratings at a service factor of 1; the hollow shaft is the bore that fits over your driven shaft, and the solid shaft is the option. The right size for your machine depends on its load, hours and starts, and we check that for you.

Housing size MA rated torque (Nm) MK rated torque (Nm) Hollow shaft bore (mm) Solid shaft (mm)
40 MA 402: 5,500
MA 403: 6,100
MK 403: 5,740
MK 404: 6,100
80 80
50 MA 502: 10,200
MA 503: 10,300
MK 503: 10,300
MK 504: 10,230
95 100
60 MA 602: 12,900
MA 603: 11,900
MK 603: 12,900
MK 604: 11,900
105 110
70 MA 702: 19,400
MA 703: 19,000
MA 704: 19,300
MK 703: 19,400
MK 704: 18,900
115 120
80 MA 802: 22,300
MA 803: 23,500
MA 804: 24,100
MK 803: 22,300
MK 804: 22,520
125 130
90 MA 902: 29,850
MA 903: 29,930
MA 904: 28,750
MK 903: 29,530
MK 904: 28,830
135 140
100 MA 1002: 34,500
MA 1003: 35,500
MA 1004: 36,000
MK 1003: 36,700
MK 1004: 37,580
150 160
110 MA 1102: 50,000
MA 1103: 50,400
MA 1104: 50,000
MK 1103: 50,000
MK 1104: 50,000
165 170
120 MA 1202: 70,000
MA 1203: 70,000
MA 1204: 70,000
MK 1203: 70,000
MK 1204: 70,000
180 180
Common to every size MA and MK series
Gearing MA: helical, parallel shaft. MK: one bevel stage with the other stages helical, right angle
Housing Monobloc, in GG20 cast iron
Gears 16MnCr5 steel, hardened to 57 HRC and ground
Motor power MA geared motors 3 to 560 kW; MK geared motors 0.75 to 315 kW
Ratios MA 3.786:1 to 423:1; MK 14.01:1 to 512:1
Output speed MA 3.3 to 370 rpm; MK 2.7 to 100 rpm
Input Solid shaft, IEC flange, or IEC flange with motor; at the side on the MA, at the front or on top on the MK
Output Hollow shaft as standard; solid shaft, flange, shrink disc and extruder outputs as options
Mounting Foot or flange mounted, or shaft mounted with I-MAK’s torque arm
Cooling Thermal ratings without cooling, and with fan and radiator, serpentine coil or heat exchanger cooling
Ambient temperature +5 to +60 °C for the gear unit, 0 to 40 °C for standard motors; ask us outside this range
Lubrication CLP gear oil to DIN 51517-3, mineral or synthetic, chosen for the operating temperature
Oil changes After the first 500 hours, then every 6,000 hours
Corrosion protection Paint systems for EN 12944 categories C2 to C5

Rated torques are from the gear unit performance tables at a service factor of 1 and an input speed of 1,400 rpm, and shaft diameters from the size table, in I-MAK’s MA MK MKE catalogue 2025, Rev.00. Where that edition’s headline ranges differ from its own tables, we show the table figures; the 2026 web edition prints the same size table and service factor 1 ratings.

Options

Options and configurations

Options are added to the type code, so a replacement can be matched exactly.

Output shafts

A hollow shaft as standard, or a solid shaft on the left, right or both sides (SL, SR, SD). Shrink discs (SDL, SDR) and splined or hardened hollow shafts are also available.

Output flanges

An output flange on the left, right or both sides (FL, FR, FD), on its own or with a solid shaft.

Inputs

A solid input shaft, an IEC B5 or B14 flange for your own motor, a NEMA flange, or an IEC flange with an integrated coupling. The input sits at the side on the MA and at the front or on top on the MK.

Motors and brakes

I-MAK motors, IE3 as standard or IE4 to order, with brake, hand release, double brake, encoder or external fan options. An explosion proof motor is also an option.

Extruder output

An extruder output on the left or right (EL, ER). For I-MAK’s extruder gear units, see the MAE and MKE series.

Backstop and torque arm

A backstop (BSL, BSR) stops the output turning back when the drive stops; tell us the direction of rotation. I-MAK’s MA-MK torque arm, with a rubber element, holds a shaft mounted unit.

Cooling and lubrication

Fan, radiator, serpentine coil or heat exchanger cooling (244 to 249), forced lubrication by pump, an expansion tank and an oil temperature sensor.

Seals, oil and paint

Fluoroelastomer (FKM) seals, reinforced bearings, synthetic or food-compatible oil, a low temperature oil for use down to -40 °C, and paint systems for EN 12944 categories C2 to C5.

Applications

Where MA and MK gear units work

I-MAK designs the MA for heavy loads on a continuous working cycle, and the MK for heavy loads and hard conditions across a wide range of applications. It names no particular industries, so we size each unit to your duty.

Heavy, continuous duty

MA units for heavy loads on a continuous working cycle

Hard conditions

MK units for heavy loads in hard conditions, with paint up to EN 12944 C5

Extruders

An extruder output option, or the MAE and MKE extruder series

Shaft mounted drives

A hollow output shaft and I-MAK’s torque arm, hung on the driven shaft

High power drives

Geared motors up to 560 kW, with cooling for continuous running

Sizing a heavy drive? Tell us the torque, speed and duty and we will size it; our guide to heavy industrial gearboxes covers the background.

Downloads

I-MAK MA and MK downloads

Current documents and tools from I-MAK. No forms, no sign-up.

MA and MK series catalogue

2025, Rev.00 · Sizes, ratings, options and dimensions · PDF

Download

Operating guide

General I-MAK operating guide, 2024 · Oil and maintenance, in four languages · PDF

Download

Online configurator

I-MAK iGuide, for choosing a gearbox online

Open

Dimension drawing

For your exact size and options · On request

Ask us

Can’t find it?

Need the drawing for your exact unit?

Send us the type code from the nameplate, or your torque and speed, and we will send the right drawing.

Replacing a gearbox

Replacing an existing MA or MK

Every MA and MK carries a nameplate. Send us its details, with a few photos, and we will match the replacement.

Read the type code

An MA or MK type code starts with the type and input, such as MAM, then the size, such as 703, and the motor, such as 180 L 4. The input position and any options follow a slash, such as G03 and BR.

What to send us

The type code, ratio, motor power and serial number from the nameplate, photos of the nameplate, shafts and mounting, and what the gear unit drives.

Mounting position

Tell us how the unit is mounted and which way up. I-MAK codes foot mounted positions P and flange mounted positions V, and the position sets the oil quantity.

Replacing another make

We can often replace a gearbox from another maker with an I-MAK unit. Send us the nameplate, shaft and mounting details and we will check the fit.

Spares and repairs

Ask us for I-MAK spares such as seals and bearings; the spare parts pages in the MA and MK catalogue help identify them. Need a repair rather than a replacement? Call us and we will talk it through.

Type code

How to read an MA or MK type code

  1. Type: MA (helical, parallel shaft) or MK (bevel helical, right angle)
  2. Input: none for a solid input shaft, P for an IEC input flange, PM for an IEC flange with motor; geared motors appear as MAM and MKM in the tables
  3. Size: the housing size, 40 to 120, and a final digit, such as 703
  4. Motor: IEC frame size, length and number of poles, such as 180 L 4
  5. Input position: after the slash, G00 to G06 on the MA and G07 to G10 on the MK, such as G03 (IEC flange or motor, left)
  6. Options: such as FR (output flange, right), SR (output shaft, right), E (encoder), BR (brake) and 353 (I-MAK motor)

Let’s find your gearbox

Looking for an MA or MK gear unit or a price?

We just need three details.

Replacing one? Send us the type code from the nameplate and a photo, and we will work from those.

1

Output torque

Continuous and peak, at the gear unit output shaft.

2

Output speed

Output rpm or the ratio, and the motor speed if you already have one.

3

Duty and layout

Hours per day, starts per hour, mounting, and parallel shaft or right angle.

Email us your detailsCall +44 (0)1535 655151

Prefer us to call you? Request a callback.

FAQs

I-MAK MA and MK questions

Anything else? Call +44 (0)1535 655151 or email sales@advanced-drives.com.

The MA is all helical, with the input and output shafts parallel. The MK has one bevel stage and the other stages helical, so it turns the drive through 90 degrees. Both share the same housing sizes and output options.

Nine housing sizes are rated up to 70,000 Nm at a service factor of 1 in I-MAK’s 2025 catalogue. The right size depends on your duty, so tell us the load, hours per day and starts per hour and we will check it.

Each size has a hollow output shaft that fits over your driven shaft, with a solid shaft as an option. The hollow bore runs from 80 mm on size 40 to 180 mm on size 120, and the solid shaft from 80 to 180 mm.

It depends on the power, duty and ambient temperature. I-MAK publishes thermal ratings for every size without cooling, and with fan and radiator, serpentine coil or heat exchanger cooling, so tell us the power and hours and we will check.

A CLP gear oil to DIN 51517-3, mineral or synthetic, with the grade chosen for the operating temperature; food-compatible and low temperature oils are options. Change it after the first 500 hours, then every 6,000 hours.

Often, yes. Send us the nameplate details, the shaft and mounting dimensions, and photos, and we will check whether an MA or MK fits as a drop-in replacement.