Home › Products › A and AE series

I-MAK A and AE Series Industrial Gear Units

Heavy duty helical gear units, up to 33,000 Nm and 487:1.

Eight housing sizes of horizontal helical gear unit for heavy industrial duty, with an AE version for extruders. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.

Get a priceSend us your nameplate details
I-MAK A series industrial gear unit

33,000Nm

Output torqueMaximum, for the largest housing size.

185kW

Motor powerIn I-MAK’s performance tables, from 0.37 kW.

8sizes

Housing sizesFrom size 180 up to size 750.

487:1

Ratio rangeFrom 1.71:1 on the A 200 up to 487:1 on the 4A 750.

Overview

The I-MAK A and AE: helical gear units for heavy industrial duty

The I-MAK A series is a family of horizontal helical gear units for heavy industrial duty. Eight housing sizes cover maximum output torques from 880 Nm up to 33,000 Nm, with ratios from 1.71:1 to 487:1 and motor powers up to 185 kW in I-MAK’s tables.

The type sets the ratio range. The A 200 covers the lowest ratios, from 1.71:1; the 2A types run up to about 49:1, the 3A types up to 310:1 and the 4A 750 up to 487:1. I-MAK designed the series for heavy duty and hard environments, with gears designed to help prevent noise and vibration through long, hard operation.

The AE is the extruder version. It shares the A’s performance tables but adds an extruder bearing housing on the output, and the 3AE 430 and 501 add an extruder output shaft as well. AE types come in sizes 225 to 750, with a smaller output shaft than the A of the same size.

Advanced Drives is the official UK supplier of I-MAK gearboxes and motors. For background on this class of gearbox, read our guide to heavy industrial gearboxes.

Which I-MAK gearbox?

Choose the A or AE for a heavy duty helical drive

Key advantages

Why choose an I-MAK A or AE

Up to 33,000 Nm

Eight housing sizes, with maximum output torque from 880 Nm up to 33,000 Nm.

A wide range of ratios

A, 2A, 3A and 4A types cover ratios from 1.71:1 up to 487:1.

An extruder version

The AE adds an extruder bearing housing on the output, in sizes 225 to 750.

Built for heavy duty

I-MAK designed the series for heavy industrial duty, with a robust housing for hard environments.

Gears for long, hard running

The gears are designed to help prevent noise and vibration through long, hard operation.

Clear oil change intervals

A first oil change after 500 hours, then one every 6,000 hours.

360° view

↻ Click and drag to rotate

Technical data

I-MAK A and AE technical specifications

Eight housing sizes across the A, 2A, 3A and 4A types, with AE extruder versions of sizes 225 to 750. I-MAK gives a maximum torque for every size except 200; the right size for your machine depends on its load, hours and starts, and we check that for you against I-MAK’s performance tables.

Size Types Maximum torque (Nm) Ratio range Output shaft, A / AE (mm) Oil (litres)
180 2A 880 6.98 to 46.02 45 / no AE 4
200 A, 2A On request 1.71 to 24.04 On request / no AE 10
225 2A, 2AE 2,040 7.32 to 46.69 55 / 35 7
275 2A, 2AE 4,107 6.26 to 47.50 65 / 40 10
350 2A, 2AE 8,000 6.50 to 48.97 80 / 60 18
430 2A, 3A, 2AE, 3AE 17,000 6.18 to 99.05 105 / 70 25
501 2A, 3A, 2AE, 3AE 27,000 7.28 to 310.01 120 / 90 32
750 3A, 4A, 3AE 33,000 15.01 to 487.32 140 / 115 65
Common to every size A and AE series
Gearing Helical, in a horizontal gear unit, with no bevel stage
Types A 200, 2A, 3A and 4A; AE extruder versions of the 2A and 3A
Maximum torque 880 to 33,000 Nm
Ratios 1.71:1 to 487:1
Motor power 0.37 to 185 kW
Output speed 1 to 820 rpm, at input speeds of 1,400, 900, 700 and 500 rpm
Output Solid shaft; AE types add an extruder bearing housing
Mounting positions P1 to P9 for A types; P1, P4 and P8 listed for AE types
Lubrication CLP gear oil to DIN 51517-3, mineral or synthetic, chosen for the operating temperature
Oil quantity One quantity per type, the same in every mounting position
Oil changes After the first 500 hours, then every 6,000 hours

Maximum torques and shaft diameters are the figures on I-MAK’s A and AE product page, not catalogue ratings; the torque for a given ratio and motor comes from the catalogue’s performance tables, and on some types, such as the 4A 750, it is well below the maximum; ratios, motor powers, speeds and oil quantities are from the performance and oil tables in I-MAK’s A series catalogue 2024, Rev.00. The catalogue prints the fifth size as 350 in its tables and 351 on its ordering page. I-MAK’s product page does not list size 200, so its torque and shaft size are on request.

Options

Options and configurations

Options are added to the type code after the slash, so a replacement can be matched exactly.

Output shafts

A solid output shaft as standard, with special dimensions, special materials, a hardened shaft, a threaded shaft or multiple keys to order (111 to 115).

Extruder version

AE types add an extruder bearing housing on the output, and the 3AE 430 and 501 an extruder output shaft. The option list also includes an extruder option, EL.

Input shafts

Input shafts to special dimensions or materials, hardened steel input shafts, special input shaft designs and a connection coupling (131 to 137).

Motor brakes

Brakes without a cooling fan for short duty, with a fan for continuous duty, or with a micro switch, for 24 V DC or 220 V AC.

Backstop

A backstop bearing stops the output turning back when the drive stops. Tell us the direction of rotation, clockwise or anticlockwise (235, 236).

Seals and bearings

Fluoroelastomer (FKM) seals, special seal designs, and reinforced input or output bearings (225, 231, 232).

Oil

Synthetic or food-compatible oil, or a low temperature oil for use down to -40 °C, all ISO VG 220 (211 to 213).

Paint, sensor and specials

Epoxy, outdoor acrylic, water-based or anti-corrosion paint, an oil temperature sensor (OTS), and special gears for a ratio outside the catalogue.

Applications

Where A and AE gear units work

I-MAK designs the A and AE for heavy industrial duty and hard environments, and names one specific use: extruders, through the AE. It names no particular industries, so we size each unit to your duty: its torque, speed, hours and starts.

Extruders

The AE types, with an extruder bearing housing on the output

Heavy industrial duty

Long, hard running where torque and service factor matter

Hard environments

A robust housing, with anti-corrosion and outdoor paint options

Slow, high torque drives

3A and 4A types, for output speeds down to 1 rpm on the 4A 750

Low ratio drives

The A 200 and 2A types, from 1.71:1, with up to 820 rpm on the A 200

Replacement units

Matching an existing helical gear unit on torque, shafts and mounting

Downloads

I-MAK A and AE downloads

Current documents and tools from I-MAK. No forms, no sign-up.

A and AE series catalogue

2024, Rev.00 · Sizes, performance tables, options and dimensions · PDF

Download

Online configurator

I-MAK iGuide, for choosing a gearbox online

Open

Dimension drawing

For your exact size and options · On request

Ask us

Can’t find it?

Need the drawing for your exact unit?

Send us the type code from the nameplate, or your torque and speed, and we will send the right drawing.

Replacing a gearbox

Replacing an existing A or AE

Every A and AE unit carries a nameplate. Send us its details, with a few photos, and we will match the replacement.

Read the type code

An A series type code gives the type, such as 3A or 3AE, then the housing size, such as 430. Any options follow a slash, such as OTS for an oil temperature sensor or 111 for special output shaft dimensions.

What to send us

The type code, ratio and serial number from the nameplate, photos of the nameplate, shafts and mounting, and what the gear unit drives. For an AE, tell us about the extruder.

Mounting position

Tell us how the unit is mounted and which way up. I-MAK lists A types for mounting positions P1 to P9 and AE types for P1, P4 and P8.

Replacing another make

We can often replace a gearbox from another maker with an I-MAK unit. Send us the nameplate, shaft and mounting details and we will check the fit.

Spares and repairs

Ask us for I-MAK spares such as seals and bearings; the parts lists in the A series catalogue help identify them. Need a repair rather than a replacement? Call us and we will talk it through.

Type code

How to read an A series type code

  1. Type: A, 2A, 3A or 4A, such as 3A
  2. Extruder version: AE in place of A, such as 3AE
  3. Housing size: 180, 200, 225, 275, 350 (351 on the ordering page), 430, 501 or 750, such as 430
  4. Options: after the slash, such as OTS (oil temperature sensor) or EL (extruder)
  5. Shafts: 111 to 115 for the output shaft, such as 113 (hardened shaft), and 131 to 137 for the input shaft
  6. Other codes: 211 to 213 for oil, 221 to 226 for seals, 231 to 236 for bearings and 251 to 256 for paint

Let’s find your gearbox

Looking for an A or AE gear unit or a price?

We just need three details.

Replacing one? Send us the type code from the nameplate and a photo, and we will work from those.

1

Output torque

Continuous and peak, at the gear unit output shaft.

2

Output speed

Output rpm or the ratio, and the motor speed if you already have one.

3

Duty and mounting

Hours per day, starts per hour, and how the unit is mounted.

Email us your detailsCall +44 (0)1535 655151

Prefer us to call you? Request a callback.

FAQs

I-MAK A and AE questions

Anything else? Call +44 (0)1535 655151 or email sales@advanced-drives.com.

Both are helical gear units and share the same performance tables. The AE is the extruder version: it adds an extruder bearing housing on the output and has a smaller output shaft than the A of the same size.

Eight housing sizes cover maximum output torques from 880 Nm up to 33,000 Nm. The right size depends on your duty, so tell us the load, hours per day and starts per hour and we will check it against I-MAK’s tables.

They are the gearbox types in I-MAK’s ordering code, and each covers a different ratio range: up to about 49:1 for the 2A, 310:1 for the 3A and 487:1 for the 4A. The A 200 covers the lowest ratios, from 1.71:1.

No. The A and AE are helical gear units with no bevel stage, so they do not turn the drive through 90 degrees. For a right-angle drive, look at the IRK or MK series.

A CLP gear oil to DIN 51517-3, mineral or synthetic, with the grade chosen for the operating temperature; food-compatible and low temperature oils are options. Change it after the first 500 hours, then every 6,000 hours, and check the level, breather and fixing bolts in between.

Often, yes. Send us the nameplate details, the shaft and mounting dimensions, and photos, and we will check whether an A or AE fits as a drop-in replacement.