I-MAK IRNX Series Shaft Mounted Gearboxes
Shaft mounted, up to 42,700 Nm, rated for a belt drive.
Shaft mounted, up to 42,700 Nm, rated for a belt drive.
Twelve sizes of shaft mounted helical gearbox for conveyors, feeders and grain storage, with hollow shafts from 30 to 190 mm. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.
42,700Nm
Output torqueMaximum, for the IRNX 12.
450kW
Motor powerFrom 0.37 kW, driving the input shaft through a belt.
12sizes
Housing sizesFrom IRNX 01 up to IRNX 12.
31:1
Gear ratioFrom 5:1, plus a belt ratio of up to 1:3.
Overview
The I-MAK IRNX series is a helical gearbox that hangs on the shaft it drives, held against turning by a torque arm, and I-MAK rates it for a belt drive from the motor. Twelve sizes cover output torques from 515 to 42,700 Nm, with motors from 0.37 to 450 kW.
I-MAK designed the IRNX for harsh industrial conditions, with a housing built for easy cleaning and dust resistance. It has two stages of helical gears in 16MnCr5 steel, and a backstop option stops a loaded inclined conveyor running back when the drive stops. I-MAK names belt, bucket and screw conveyors, apron feeders and grain storage among its uses, along with mining and cement.
I-MAK sets out the IRNX performance tables by belt pulley ratio. With a 1:1 pulley ratio and a 1,400 rpm motor, output speeds run from about 46 to 285 rpm; larger ratios, up to 1:3, slow the gearbox input to as little as a third of motor speed. Across all the tables, output speeds run from 7.6 to 569 rpm.
Advanced Drives is the official UK supplier of I-MAK gearboxes and motors. For background on how this type of gearbox works, read our guide to shaft mounted gearboxes.
Which I-MAK gearbox?
Key advantages
Twelve sizes, with output torque from 515 Nm up to 42,700 Nm.
Tables for pulley ratios of 1:1 to 1:3 make it simple to choose the output speed and motor.
A backstop bearing stops a loaded inclined conveyor running back when the drive stops.
The hollow output shaft goes straight onto the driven shaft, for quick fitting and quick maintenance.
Rubber rings in the torque arm resist shocks and absorb vibration from the housing and output shaft.
I-MAK designed the housing for easy cleaning and resistance to dust.
360° view
↻ Click and drag to rotate
Technical data
Twelve sizes, each a gear unit with an input shaft and a hollow output shaft. The torque figures are the maximum output torque I-MAK prints for each size in its performance tables; the right size for your machine depends on its load, hours and starts, and we check that for you.
| Size | Maximum output torque (Nm) | Hollow shaft diameter (mm) | Input shaft, diameter x length (mm) |
|---|---|---|---|
| IRNX 01 | 515 | 30 | 19 x 40 |
| IRNX 02 | 815 | 40 | 22 x 45 |
| IRNX 03 | 1,290 | 50 | 25 x 55 |
| IRNX 04 | 1,800 | 50 | 28 x 60 |
| IRNX 05 | 3,160 | 60 | 32 x 70 |
| IRNX 06 | 4,690 | 70 | 42 x 90 |
| IRNX 07 | 7,460 | 85 | 48 x 100 |
| IRNX 08 | 9,920 | 100 | 55 x 128 |
| IRNX 09 | 12,420 | 120 | 60 x 168 |
| IRNX 10 | 17,900 | 125 | 60 x 168 |
| IRNX 11 | 24,460 | 150 | 65 x 190 |
| IRNX 12 | 42,700 | 190 | Ask us |
| Common to every size | IRNX series |
|---|---|
| Gearing | Two helical gear pairs |
| Gears | 16MnCr5 steel |
| Gear ratios | Two to four ratios per size: between 5:1 and 31:1 for sizes 01 to 08, and between 12:1 and 21:1 for sizes 09 to 12 |
| Belt drive | Pulley ratios of 1:1 to 1:3, with motors at 700, 900, 1,400 or 2,800 rpm |
| Motor power | 0.37 to 450 kW |
| Output speeds | 7.6 to 569 rpm across the tables |
| Duty ratings | Maximum motor power for light, moderate and heavy load, at 8, 16 and 24 hours a day |
| Output | Hollow shaft as standard; splined, hardened and special hollow shafts as options |
| Mounting | On the driven shaft, held by a torque arm with rubber rings |
| Backstop | Option, ordered for clockwise or anticlockwise rotation |
| Lubrication | CLP mineral or CLP HC synthetic gear oil to DIN 51517-3, chosen for the operating temperature |
| Oil changes | After the first 500 hours, then every 6,000 hours |
Torques, ratios and speeds are from I-MAK’s IRNX performance tables, the 0.37 to 450 kW motor range from the catalogue’s headline data, and shaft sizes from its overhung load tables; the IRNX 12 hollow shaft is from I-MAK’s IRNX product data. Source: I-MAK IRNX catalogue 2024, Rev.00.
Applications
I-MAK names the IRNX for bulk material transport, mining and cement, and for conveyors and grain storage: heavy, dusty duties where the gearbox sits directly on the driven shaft.
Including inclined conveyors, with the backstop option
Moving bulk material in buckets or along a screw
Apron feeders moving heavy bulk material, and roller beds
With the gearbox mounted directly on the mixer shaft
Conveyors serving grain stores and silos
Sizing a conveyor drive? Our guide to conveyor torque covers the figures we will ask you for.
Can’t find it?
Send us the type code from the nameplate, or your torque and speed, and we will send the right drawing.
Replacing a gearbox
Every I-MAK gearbox carries a nameplate. Send us the details on it, with a few photos, and we will match the replacement.
An IRNX type code is the series and the size, from 01 to 12, such as IRNX 05. Any options follow a slash, such as BSL (backstop left).
The type code, ratio and serial number from the nameplate, the motor power and speed, the pulley sizes, photos of the nameplate, shafts and torque arm, and what the gearbox drives.
Tell us how the unit hangs on the shaft and which way up. The mounting position sets the oil quantity, and I-MAK publishes the IRNX positions as drawings.
We can often replace a gearbox from another maker with an I-MAK unit. Send us the nameplate, shaft and mounting details and we will check the fit.
Ask us for I-MAK spares such as seals and bearings; the parts list in the IRNX catalogue helps identify them. Need a repair rather than a replacement? Call us and we will talk it through.
Type code
Let’s find your gearbox
We just need three details.
Replacing one? Send us the type code from the nameplate and a photo, and we will work from those.
1
Continuous and peak, at the driven shaft.
2
Output rpm, the motor power and speed, and the pulley ratio if you have one.
3
Hours per day, how heavy the load is, the driven shaft diameter, and whether it needs a backstop.
Prefer us to call you? Request a callback.
FAQs
Anything else? Call +44 (0)1535 655151 or email sales@advanced-drives.com.
A gearbox with a hollow output shaft that slides straight onto the shaft it drives, such as a conveyor drive pulley shaft. A torque arm stops the housing turning; on the IRNX, rubber rings in the torque arm absorb shocks and vibration.
I-MAK rates the IRNX for a belt drive from the motor to the input shaft. A 1:1 ratio uses equal pulleys, while a 1:2 or 1:3 ratio slows the input to a half or a third of motor speed, and the output slows with it. For each case, the tables give the largest motor for light, moderate or heavy load at 8, 16 or 24 hours a day.
From 515 Nm for the IRNX 01 up to 42,700 Nm for the IRNX 12, the maximum output torque in I-MAK’s tables. The right size depends on your load and hours, so tell us your duty and we will check it.
I-MAK lists it as an option, ordered with the gearbox. A backstop bearing stops the output turning back when the drive stops, which matters on an inclined conveyor carrying a load. Tell us the direction of rotation, clockwise or anticlockwise, when you order.
A CLP mineral or CLP HC synthetic gear oil to DIN 51517-3, with the grade chosen for the operating temperature; food-compatible and low temperature oils are options. Change it after the first 500 hours, then every 6,000 hours.
Often, yes. Send us the nameplate details, the shaft and mounting dimensions, and photos, and we will check whether an IRNX fits as a drop-in replacement.