Home › Products › MAE and MKE series
I-MAK MAE and MKE Series Monobloc Extruder Gear Units
Extruder gear units, helical or right angle, up to 70,000 Nm.
Home › Products › MAE and MKE series
Extruder gear units, helical or right angle, up to 70,000 Nm.
Nine housing sizes of monobloc gear unit, with an output built to carry the axial load from an extruder screw. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.
70,000Nm
Output torqueMaximum, for the largest housing size.
560kW
Motor powerUp to 560 kW on the MAE and 250 kW on the MKE.
9sizes
Housing sizesFrom size 40 up to size 120, as MAE or MKE.
512:1
Ratio rangeFrom 6.028:1 on the MAE, up to 512:1 on the MKE.
Overview
The MAE and MKE are the extruder versions of I-MAK’s monobloc gear units. The MAE follows the helical MA family and the MKE the bevel helical, right-angle MK family, across nine housing sizes with maximum torque up to 70,000 Nm.
The output is a hollow shaft that takes the extruder screw shank, and I-MAK designs it to carry the high axial load the screw puts on the gear unit. I-MAK also gives the MAE and MKE larger roller bearings and extended centre distances, so they can take higher loads.
The housing is a single casting in cast iron, and the gears are 16MnCr5 steel, hardened to 57 HRC and ground. IEC or NEMA inputs, backstop and brake options, a range of cooling and lubrication options, and horizontal or vertical mounting are all available. I-MAK publishes no thrust rating, so tell us the screw thrust and we will check the selection.
Advanced Drives is the official UK supplier of I-MAK gearboxes and motors.
Which I-MAK gearbox?
Key advantages
The output is designed to carry the high axial load from an extruder screw.
Nine housing sizes, with maximum torque from 6,080 Nm up to 70,000 Nm.
Larger roller bearings and extended centre distances, so the unit can take higher loads.
The MAE is helical, in the MA family; the MKE adds a bevel stage for a right-angle drive.
16MnCr5 steel gears, hardened to 57 HRC and ground.
The hollow output shaft takes the screw shank, and the bore can be made to suit your screw.
360° view
↻ Click and drag to rotate
Technical data
Nine housing sizes, as the helical MAE or the right-angle MKE. The torque figures are I-MAK’s maximum for each size group, and the hollow shaft is the bore that takes the screw shank. The right size for your extruder depends on its torque, speed, screw thrust and hours, and we check that for you.
| Housing size | MAE maximum torque (Nm) | MKE maximum torque (Nm) | Hollow shaft bore (mm) |
|---|---|---|---|
| 40 | MAE 402-403: 6,080 | MKE 403-404: 6,100 | 60 |
| 50 | MAE 502-503: 10,300 | MKE 503-504: 10,300 | 70 |
| 60 | MAE 602-603: 12,900 | MKE 603-604: 12,900 | 80 |
| 70 | MAE 702-703-704: 19,400 | MKE 703-704: 19,400 | 90 |
| 80 | MAE 802-803-804: 24,100 | MKE 803-804: 22,520 | 100 |
| 90 | MAE 902-903-904: 29,930 | MKE 903-904: 29,530 | 110 |
| 100 | MAE 1002-1003-1004: 36,000 | MKE 1003-1004: 37,580 | 120 |
| 110 | MAE 1102-1103-1104: 50,000 | MKE 1103-1104: 50,000 | 130 |
| 120 | MAE 1202-1203-1204: 70,000 | MKE 1203-1204: 70,000 | 180 or 140, to be confirmed |
| Common to every size | MAE and MKE series |
|---|---|
| Gearing | MAE: helical, in the MA family. MKE: bevel helical, right angle, in the MK family |
| Housing | Monobloc, in cast iron |
| Gears | 16MnCr5 steel, hardened to 57 HRC and ground |
| Thrust capacity | Not published by I-MAK; tell us your screw thrust and we will check the selection |
| Ratios | MAE 6.028:1 to 423:1; MKE 15.674:1 to 512:1 |
| Motor power | MAE 2.2 to 560 kW; MKE 0.55 to 250 kW |
| Input | Solid shaft, IEC flange with coupling, or IEC flange with motor; IEC and NEMA configurations |
| Output | Hollow shaft for the screw shank; the bore can be made to suit your screw |
| Mounting | Horizontal or vertical |
| Cooling | Fan, radiator, serpentine coil and heat exchanger options |
| Ambient temperature | +5 to +60 °C for the gear unit, 0 to 40 °C for standard motors; ask us outside this range |
| Lubrication | CLP gear oil to DIN 51517-3, mineral or synthetic, chosen for the operating temperature |
| Oil changes | After the first 500 hours, then every 6,000 hours |
| Corrosion protection | Paint systems for EN 12944 categories C2 to C5 |
Torques, hollow shaft bores, ratios and motor powers are from the MAE and MKE size table in I-MAK’s MA MK MKE catalogue 2025, Rev.00, which shares its options, oil and maintenance pages with the MA and MK; gear materials and bearings are from I-MAK’s MAE and MKE product data. Ratios and motor powers are the ranges printed in that size table; the MA and MK performance tables, quoted on our MA and MK page, run to slightly different limits. For size 120 the catalogue prints a 180 mm bore and I-MAK’s product page 140 mm, so we confirm it for each order. I-MAK publishes no performance tables, output speeds or thrust ratings for the extruder versions, so ask us to check a selection against your duty.
Applications
I-MAK builds the MAE and MKE for extruders and other heavy applications. It does not name particular materials or industries, so we size each unit to your extruder: its torque, speed, screw thrust and hours.
Driving the screw, with the output built to carry its axial load
The MKE, where the motor sits at 90 degrees to the screw
Mounting to suit the machine, in either orientation
Other high load drives, with larger bearings for higher loads
Motors up to 560 kW, with cooling options for long running
Matched on screw shank bore, thrust, torque and mounting
Can’t find it?
Send us the type code from the nameplate, or your torque and speed, and we will send the right drawing.
Replacing a gearbox
Every MAE and MKE carries a nameplate. Send us its details, with a few photos and the screw shank dimensions, and we will match the replacement.
I-MAK names these units by type and size, such as MAE 703 or MKE 1004. The catalogue’s ordering code is written for the MA and MK, so send us the full nameplate and we will read it for you.
The type code, ratio, motor power and serial number from the nameplate, photos of the nameplate, shafts and mounting, the screw shank dimensions and the screw thrust if you know it.
Tell us how the unit is mounted, horizontal or vertical, and which way up. The mounting position sets the oil quantity.
We can often replace a gearbox from another maker with an I-MAK unit. Send us the nameplate, the screw shank bore and the mounting details and we will check the fit.
Ask us for I-MAK spares such as seals and bearings. Need a repair rather than a replacement? Call us and we will talk it through.
Type code
Let’s find your gearbox
We just need three details.
Replacing one? Send us the type code from the nameplate and a photo, and we will work from those.
1
Continuous and peak torque at the screw, and the screw speed or ratio.
2
The axial load from the screw, and the screw shank diameter.
3
Hours per day, starts per hour, mounting, and helical or right angle.
Prefer us to call you? Request a callback.
FAQs
Anything else? Call +44 (0)1535 655151 or email sales@advanced-drives.com.
They are the extruder versions. I-MAK designs the output to carry the high axial load from the extruder screw, with larger roller bearings and extended centre distances, and the hollow output shaft takes the screw shank.
I-MAK does not publish a thrust rating for these units. Tell us the screw thrust, torque and speed when you enquire and we will check the selection.
The MAE is helical, in the MA family. The MKE has a bevel stage, in the MK family, so it turns the drive through 90 degrees.
The 2025 catalogue lists hollow shaft bores from 60 mm on size 40 to 130 mm on size 110, and 180 mm on size 120, although I-MAK’s product page gives 140 mm, so we confirm it for each order. The bore can be made to suit your screw, so send us the shank dimensions.
A CLP gear oil to DIN 51517-3, mineral or synthetic, with the grade chosen for the operating temperature; food-compatible and low temperature oils are options. Change it after the first 500 hours, then every 6,000 hours.
Often, yes. Send us the nameplate details, the screw shank bore, the mounting dimensions and photos, and we will check whether an MAE or MKE fits.