Home › Products › S series

I-MAK S Series Worm Geared Motors

Compact worm drive, from 13 to 1,554 Nm and 0.12 to 15 kW.

Nine sizes of worm gearbox and geared motor, from the 1 kg S 30 upwards, with a hollow output shaft as standard. Genuine I-MAK units, supplied and supported from Silsden, West Yorkshire.

Get a priceSend us your nameplate details
I-MAK S worm geared motor

1,554Nm

Output torqueS 150 gear unit at 1,400 rpm input; 1,790 Nm at 900 rpm.

15kW

Motor powerGeared motors from 0.12 kW upwards.

9sizes

Housing sizesFrom S 30 up to S 150.

5,000:1

Ratio rangeFrom 7.5:1, with two units combined for the highest ratios.

Overview

The I-MAK S: a compact, modular worm gearbox

The I-MAK S series turns the drive through 90 degrees with a single worm and worm wheel stage. Nine housing sizes cover rated output torques from 13 Nm up to 1,554 Nm, as a gearbox on its own or as a geared motor from 0.12 to 15 kW.

I-MAK builds the S with an aluminium or a cast iron housing, and lists low noise and low vibration among the series’ strengths. Ratios run from 7.5:1 to 100:1 in a single housing, and on S 50 to S 150, two S units combined reach 5,000:1.

Every S is foot mounted with a hollow output shaft as standard. Bolt-on output flanges and output shafts make it a flange mounted or solid shaft unit, and a torque arm lets it hang on the driven shaft. With the backstop option it also suits drives that must not run back, such as inclined conveyors.

Advanced Drives is the official UK supplier of I-MAK gearboxes and motors. For background on how this type of gearbox works, read our guide to worm gearboxes.

Which I-MAK gearbox?

Choose the S for compact worm drives

Key advantages

Why choose an I-MAK S gearbox

Up to 1,554 Nm

Nine housing sizes, rated from 13 Nm up to 1,554 Nm at 1,400 rpm input, and 1,790 Nm at 900 rpm.

Compact and light

The S 30 gear unit weighs 1 kg and the S 90 13 kg, without a motor.

High ratios in one stage

Ratios from 7.5:1 to 100:1 from a single worm stage give low output speeds from a standard motor.

Up to 5,000:1 combined

Two S units combined take the ratio up to 5,000:1.

Same oil quantity, any position

From S 30 to S 90, the oil quantity does not change with the mounting position.

Clear oil change intervals

A first oil change after 500 hours, then one every 6,000 operating hours.

360° view

↻ Click and drag to rotate

Technical data

I-MAK S technical specifications

Nine housing sizes, each available as a gearbox or a geared motor. The torque figures are I-MAK’s ratings at a service factor of 1, for an input speed of 1,400 rpm and of 900 rpm; the right size for your machine depends on its load, hours and starts, and we check that for you.

Size Rated torque at 1,400 rpm input (Nm) Rated torque at 900 rpm input (Nm) Ratio range Gear unit weight (kg)
S 30 21 22 7.5 to 80 1
S 40 42 43 7.5 to 100 2
S 50 71 80 7.5 to 100 4
S 63 145 162 7.5 to 100 6
S 75 221 242 7.5 to 100 9
S 90 410 460 7.5 to 100 13
S 110 728 836 7.5 to 100 40
S 130 1,056 1,167 7.5 to 100 53
S 150 1,554 1,790 7.5 to 100 84
Common to every size S series
Gearing A single worm and worm wheel stage
Housing Aluminium or cast iron; ask us which applies to your size
Motor power 0.12 to 15 kW
Ratios 7.5:1 to 100:1; up to 5,000:1 with two units combined, S 50 to S 150
Output speed 14 to 187 rpm at 1,400 rpm input
Efficiency 45 to 91% at 1,400 rpm input, lower at higher ratios
Output Hollow shaft as standard; solid shaft and output flange options
Mounting Foot mounted as standard; flange mounted with an output flange, or shaft mounted with a torque arm; positions P1 to P6 and V1 to V6
Oil quantity S 30 to S 90: 0.04 to 1 litre, the same in every mounting position; S 110 to S 150: 2.2 to 7 litres, by position
Ambient temperature Gear unit +5 to +60 °C, standard motor 0 to 40 °C; ask us outside these ranges
Lubrication CLP gear oil, mineral or synthetic, chosen for the operating temperature
Oil changes After the first 500 hours, then every 6,000 operating hours
Standard motor IE3, IP 55, insulation class F, 400 V 50 Hz

Torque ratings, ratios, efficiencies and weights are from I-MAK’s worm gear unit performance tables at a service factor of 1; weights are for the gear unit without a motor. Source: I-MAK S, IRS and IRSD catalogue 2025, Rev.00, and the I-MAK operating guide for the S, IRS and IRSD series.

Options

Options and configurations

Options are added to the type code, so a replacement can be matched exactly.

Output shafts

A hollow shaft as standard, or a solid output shaft on the left, right or both sides. Splined and special hollow shafts are also available.

Output flanges

A flange on the left, right or both sides makes the S a flange mounted unit. An output cover is also available.

Inputs

A solid input shaft, a double input shaft, or an IEC B14 or B5 input flange for your own motor.

Motors and brakes

Geared motors from 0.12 to 15 kW, with brake, hand release, double brake, encoder or external cooling fan options. Single phase and explosion proof motors are also available.

Backstop

Stops the output turning back when the drive stops, for example on an inclined conveyor. On the S it is fitted at the motor side; tell us the direction of rotation.

Torque arm

A torque arm on the left or right holds a shaft mounted unit against the reaction torque.

Seals, bearings and oil

Fluoroelastomer (FKM) seals, dust covers, reinforced input or output bearings, synthetic or food-compatible oil, and a low temperature oil for use down to -40 °C.

Paint and motor protection

Epoxy, outdoor acrylic and anti-corrosion paints, motor protection up to IP 66, and thermistor or PT 100 sensors.

Applications

Where S gearboxes work

I-MAK offers the S for a wide range of applications. It suits drives that need a high ratio from a compact, right-angle unit, from 0.12 kW upwards.

Conveyors

Conveyors that need a high ratio and a low output speed

Inclined conveyors

With the backstop option, so the load cannot run back when the drive stops

Compact machines

Where space is tight and the drive has to turn through 90 degrees

Shaft mounted drives

Hung on the driven shaft with the hollow output and a torque arm

Small drives

Geared motors from 0.12 kW for small, slow-running machines

Not sure how to mount it? Our guide to gearbox mounting positions explains the choices.

Downloads

I-MAK S downloads

Current documents and tools from I-MAK. No forms, no sign-up.

S, IRS and IRSD catalogue

2025, Rev.00 · Sizes, ratings, options and dimensions · PDF

Download

Operating guide

S, IRS and IRSD series · Installation, oil and maintenance · PDF

Download

Online configurator

I-MAK iGuide, for choosing a gearbox online

Open

Dimension drawing

For your exact size and options · On request

Ask us

Can’t find it?

Need the drawing for your exact unit?

Send us the type code from the nameplate, or your torque and speed, and we will send the right drawing.

Replacing a gearbox

Replacing an existing S gearbox

Every S carries a nameplate. Send us its details, with a few photos, and we will match the replacement.

Read the type code

An S type code starts with the series and input, such as SM for a geared motor, then the housing size, such as 63, and the motor, such as 80 M 4. Any options follow a slash.

What to send us

The type code, ratio, motor power and serial number from the nameplate, photos of the nameplate, shafts and mounting, and what the gearbox drives.

Mounting position

Tell us how the unit is mounted and which way up, using I-MAK’s positions P1 to P6 or V1 to V6. On the S 110 to S 150 the mounting position also sets the oil quantity.

Replacing another make

We can often replace a gearbox from another maker with an I-MAK unit. Send us the nameplate, shaft and mounting details and we will check the fit.

Spares and repairs

Ask us for I-MAK spares such as seals and bearings; the parts lists in the catalogue help identify them. Need a repair rather than a replacement? Call us and we will talk it through.

Type code

How to read an S type code

  1. Series: S
  2. Mounting: no letter, as every S is foot mounted; an output flange option makes it flange mounted
  3. Input: none for a solid input shaft, M with a motor, P with an IEC input flange
  4. Housing size: from 30 to 150, such as 63
  5. Motor: IEC frame size, length and number of poles, such as 80 M 4
  6. Options: after the slash, such as FR (output flange, right), SR (output shaft, right), C (double input shaft) and BR (brake)

Let’s find your gearbox

Looking for an S gearbox or a price?

We just need three details.

Replacing one? Send us the type code from the nameplate and a photo, and we will work from those.

1

Output torque

Continuous and peak, at the gearbox output shaft.

2

Output speed

Output rpm or the ratio, and the motor speed if you already have one.

3

Duty and mounting

Hours per day, starts per hour, and how the unit is mounted.

Email us your detailsCall +44 (0)1535 655151

Prefer us to call you? Request a callback.

FAQs

I-MAK S series questions

Anything else? Call +44 (0)1535 655151 or email sales@advanced-drives.com.

I-MAK’s catalogue lists the S with an aluminium or a cast iron housing. Tell us the size you need and we will confirm which housing it has.

Nine housing sizes cover rated output torques from 13 Nm up to 1,554 Nm at 1,400 rpm input, and 1,790 Nm at 900 rpm, at a service factor of 1. The right size depends on your duty, so tell us the load, hours per day and starts per hour and we will check it.

Do not rely on the worm gearing for that. I-MAK does not publish self-locking data for the S, so where the load must not run back, use the backstop option, a motor brake, or both.

Tell us first. Food-compatible oil is an option, and I-MAK asks to be told about use in food processing so the unit can be adapted; the gearbox should not come into direct contact with the food.

A CLP gear oil, mineral or synthetic, with the grade chosen for the operating temperature; we confirm the fill for your size and mounting position when you order. Change it after the first 500 hours, then every 6,000 operating hours.

Often, yes. Send us the nameplate details, the shaft and mounting dimensions, and photos, and we will check whether an S fits as a drop-in replacement.